Smart_PDU_L/protocol/SPI/spi.c

#include "gd32f30x.h"
#include "gd32f30x_it.h"
#include "gd32f30x_spi.h"
#include "gd32f30x_rcu.h"
#include "gd32f30x_gpio.h"

volatile uint32_t send_n = 0, receive_n = 0;
uint8_t spi0_send_array[ARRAYSIZE] = {0xA1, 0xA2, 0xA3, 0xA4, 0xA5, 0xA6, 0xA7, 0xA8, 0xA9, 0xAA };
uint8_t spi1_receive_array[ARRAYSIZE];

void rcu_config(void);
void gpio_config(void);
void spi_config(void);
ErrStatus memory_compare(uint8_t *src, uint8_t *dst, uint8_t length);

/*!
    \brief      main function
    \param[in]  none
    \param[out] none
    \retval     none
*/
int main(void)
{
    /* initialize the LEDs */
\
    /* configure NVIC */
    nvic_priority_group_set(NVIC_PRIGROUP_PRE1_SUB3);
    nvic_irq_enable(SPI0_IRQn, 1, 1);
    nvic_irq_enable(SPI1_IRQn, 0, 1);

    /* enable peripheral clock */
    rcu_config();
    /* configure GPIO */
    gpio_config();
    /* configure SPI */
    spi_config();

    /* enable SPI interrupt */
    spi_i2s_interrupt_enable(SPI0, SPI_I2S_INT_TBE);
    spi_i2s_interrupt_enable(SPI1, SPI_I2S_INT_RBNE);

    /* enable SPI */
    spi_enable(SPI1);
    spi_enable(SPI0);

    /* wait transmit completed */
    while(receive_n < ARRAYSIZE);

#if SPI_CRC_ENABLE
    /* check the CRC error status  */
    if(SET != spi_i2s_flag_get(SPI1, SPI_FLAG_CRCERR)) {
        gd_eval_led_on(LED1);
    } else {
        gd_eval_led_off(LED1);
    }
#else
    /* compare receive data with send data */
    if(ERROR != memory_compare(spi1_receive_array, spi0_send_array, ARRAYSIZE)) {
        gd_eval_led_on(LED1);
    } else {
        gd_eval_led_off(LED1);
    }
#endif /* enable CRC function */

    while(1) {
    }
}

/*!
    \brief      configure different peripheral clocks
    \param[in]  none
    \param[out] none
    \retval     none
*/
void rcu_config(void)
{
    rcu_periph_clock_enable(RCU_GPIOA);
    rcu_periph_clock_enable(RCU_GPIOB);
    rcu_periph_clock_enable(RCU_SPI0);
    rcu_periph_clock_enable(RCU_SPI1);
}

/*!
    \brief      configure the GPIO peripheral
    \param[in]  none
    \param[out] none
    \retval     none
*/
void gpio_config(void)
{
    /* configure SPI0 GPIO: SCK/PA5, MOSI/PA7 */
    gpio_af_set(GPIOA, GPIO_AF_0, GPIO_PIN_5 | GPIO_PIN_7);
    gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_PIN_5 | GPIO_PIN_7);
    gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_5 | GPIO_PIN_7);

    /* configure SPI1 GPIO: SCK/PB13, MISO/PB14 */
    gpio_af_set(GPIOB, GPIO_AF_0, GPIO_PIN_13 | GPIO_PIN_14);
    gpio_mode_set(GPIOB, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_PIN_13 | GPIO_PIN_14);
    gpio_output_options_set(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_13 | GPIO_PIN_14);
}

/*!
    \brief      configure the SPI peripheral
    \param[in]  none
    \param[out] none
    \retval     none
*/
void spi_config(void)
{
    spi_parameter_struct  spi_init_struct;
    /* deinitialize SPI and the parameters */
    spi_i2s_deinit(SPI0);
    spi_i2s_deinit(SPI1);
    spi_struct_para_init(&spi_init_struct);

    /* configure SPI0 parameter */
    spi_init_struct.trans_mode           = SPI_TRANSMODE_BDTRANSMIT;
    spi_init_struct.device_mode          = SPI_MASTER;;
    spi_init_struct.frame_size           = SPI_FRAMESIZE_8BIT;;
    spi_init_struct.clock_polarity_phase = SPI_CK_PL_HIGH_PH_2EDGE;
    spi_init_struct.nss                  = SPI_NSS_SOFT;
    spi_init_struct.prescale             = SPI_PSC_32 ;
    spi_init_struct.endian               = SPI_ENDIAN_MSB;;
    spi_init(SPI0, &spi_init_struct);

    /* configure SPI1 parameter */
    spi_init_struct.trans_mode           = SPI_TRANSMODE_BDRECEIVE;
    spi_init_struct.device_mode          = SPI_SLAVE;
    spi_init(SPI1, &spi_init_struct);

#if SPI_CRC_ENABLE
    /* configure SPI CRC function */
    spi_crc_polynomial_set(SPI0, 7);
    spi_crc_polynomial_set(SPI1, 7);
    spi_crc_on(SPI0);
    spi_crc_on(SPI1);
#endif /* enable CRC function */
}

/*!
    \brief      memory compare function
    \param[in]  src: source data pointer
    \param[in]  dst: destination data pointer
    \param[in]  length: the compare data length
    \param[out] none
    \retval     ErrStatus: ERROR or SUCCESS
*/
ErrStatus memory_compare(uint8_t *src, uint8_t *dst, uint8_t length)
{
    while(length--) {
        if(*src++ != *dst++) {
            return ERROR;
        }
    }
    return SUCCESS;
}



void SPI0_Init(void)
{
	//init perhapeis closk;
		rcu_periph_clock_enable(RCU_GPIOA);
    rcu_periph_clock_enable(RCU_SPI0);
		//
		gpio_af_set(GPIOA, GPIO_AF_0, GPIO_PIN_5 | GPIO_PIN_7);
    gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_PIN_5 | GPIO_PIN_7);
    gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_5 | GPIO_PIN_7);
}