#include "gd32e23x.h"
#include "systick.h"
#include <stdio.h>
#include "main.h"
#include "Fwdgt.h"
#include "mb.h"
#include "Led.h"
#include "Key.h"
#include "cfg.h"
#include "gd32e23x_fmc.h"
#include "string.h"
#include "Timer.h"
#include "Fwdgt.h"
#include "stdbool.h"
#include "At24cxx.h"
#include "Sn74hc573.h"
#include "Relay.h"
#include "ReadEeprom.h"
#include "Uart1.h"
#include "Hlw8110.h"
#include "key_io.h"
#include "Flash.h"
#include "board_cfg.h"



AC_Output_struct_Reg  			AC3PPDU_Output[Output_ChN_default + 2] = {0}; 
AC3PPDU_RELAY_Para_Reg 			AC3PPDU_RL_time[Output_ChN_default + 2] = {0};
AC3PPDU_RELAY_Para_Reg 			AC3PPDU_RL_N_time;	


static uint8_t 							AC3PPDU_SlaveAddress = 0x00;
uint16_t 										Devid_IDChalNum = 0;


bool RL_Allon_flag 																				= false;
bool RL_Alloff_flag 																			= false;
bool Start_Read_Flag 																			= false;

uint16_t 			CurrentAddr 														= 0;
uint8_t 			flash_flag = 0;
uint32_t 			AC3PPDU_Modbus_Reg[AC3PPDU_Modbus_Reg_len] = {0};
uint8_t 			AC3PPDU_active_chn = Output_ChN_default;
information_t infomation;
uint32_t 			hlw8110_base[Output_ChN_default + 1] = {0}; //add by liyi
uint8_t 			Wr_eeprom_cnt = 0;


uint8_t RL_begin_delay_flag[Output_ChN_default+1] 	= {0x00};
uint8_t RL_end_delay_flag[Output_ChN_default+1] 		= {0x00};
uint8_t RL_ON_flag[Output_ChN_default+1] 						= {0x00};
uint8_t RL_OFF_flag[Output_ChN_default+1] 					= {0x00};
uint8_t RL_last_state[Output_ChN_default+1] 				= {0x00};
uint8_t RL_now_state[Output_ChN_default+1] 					= {0x00};
uint8_t RL_Func_statu[Output_ChN_default + 1] 			= {0x00};
uint8_t RL_All_Func 																= 0x0;
uint32_t normal_running_time = 0;


#if SUPPORT_ZERO_LINE

uint8_t RL_N_begin_delay_flag 											= 0x0;  					// add by liyi
uint8_t RL_N_end_delay_flag 												= 0x0;						// add by liyi
uint8_t RL_N_ON_flag 																= 0x0;						// add by liyi
uint8_t RL_N_OFF_flag 															= 0x0;						// add by liyi
uint8_t RL_N_last_state															=	0x0;						// add by liyi
uint8_t RL_N_now_state															=	0x0;						// add by liyi

#endif

uint8_t AC3PPDU_Vmax_LTen_flag[Output_ChN_default+1] = {0x01};
uint8_t AC3PPDU_Vmin_LTen_flag[Output_ChN_default+1] = {0x01};
uint8_t AC3PPDU_Imax_LTen_flag[Output_ChN_default+1] = {0x01};
uint8_t AC3PPDU_Wmax_LTen_flag[Output_ChN_default+1] = {0x01};
uint8_t AC3PPDU_kWhmax_LTen_flag[Output_ChN_default+1] = {0x01};

bool orderFlag[Output_ChN_default] ={0};

bool orderFlag_N = 0;


uint32_t AC_BASE[4] 																		= {0};
META_DATA_S meta_data 																	= {0};
uint8_t write_kwh2Eeprom_flag 													= 0;
uint8_t detection_value = 0;

extern float 										hlw8110_store[Output_ChN_default + 1];
extern uint32_t 								Modbus_Wr_buff[Mb_Wcmd_Width][Mb_Wcmd_len];
extern uint32_t 								RL_N_delay_cnt;																										// add by liyi
extern uint32_t 								RL_N_delay_Limit;																								// add by liyi
extern uint32_t 								RL_delay_Limit[Output_ChN_default + 1];


static void MODbus_CMD_New(void);
static void Fault_state_process(uint8_t ch_x);




static void break_2_boot_upgreade(void)
{
	meta_data.errno = 0;
	meta_data.operation_flag = 1;
	meta_data.recent_running_time = normal_running_time;
	flash_erase_meta();
	flash_write_meta(&meta_data);
	__disable_irq();
	//__set_FAULTMASK(1);
	NVIC_SystemReset();
}


static void app_init(META_DATA_S *meta)
{
	flash_get_meta_data(meta);
	nvic_vector_table_set(NVIC_VECTTAB_FLASH,meta->rom_addr - NVIC_VECTTAB_FLASH);
	__enable_irq();
}

static bool select_channel(uint8_t ch_x)
{
	if(ch_x == 0)
		return false;
	switch(ch_x)
	{
		case CH1_out:
		{
				SEL_0_H;
				SEL_1_H;
				SEL_2_H;
		}
			break;
		case CH2_out:
		{
				SEL_0_L;
				SEL_1_H;
				SEL_2_H;
		}
			break;
		case CH3_out:
		{
				SEL_0_H;
				SEL_1_L;
				SEL_2_H;
		}
			break;
		default:
			return false;
	}
	return true;
}

void hlw8110_init(uint8_t ch_x)
{
	if(select_channel(ch_x) == false)
		return;
	Init_HLW8110();
}


static void  check_jlink()
{
#if SUPPORT_RELAY_CTRL
	#if SUPPORT_KEY_CTRL
		uint8_t test = false;
		uint8_t rst = false;
	#endif
	if(Chk_Jlink_conn() == false)
	{
#if SUPPORT_KEY_CTRL
			rst = get_rst();
			
			test = get_test();
		#if SUPPORT_DETECTION
			if(detection_value == false)			// duan lu qi shi fou zai xian
			{
				for(int i = 0; i < Output_ChN_default;i++)
				{
					AC3PPDU_RL_time[i + CH1_out].LT_state &=0xffffff7e;
					orderFlag[i]=true;
				}
			}else
		#endif
			{
				if(rst != test)					//shou dong kai guan
				{
					if(rst)
					{
						for(int k = 0; k < Output_ChN_default;k++)
						{
							AC3PPDU_RL_time[k + CH1_out].LT_state &= 0xffffff7e;
							orderFlag[k]=true;
						}
					}else
					{
						for(int k = 0; k < Output_ChN_default;k++)
						{
							AC3PPDU_RL_time[k + CH1_out].LT_state &= 0xffffffbf;
							AC3PPDU_RL_time[k + CH1_out].LT_state |= 0x00000001;
							orderFlag[k]=true;
						}
						
					}
				}
			}
#else
	#if SUPPORT_DETECTION
		if(detection_value == false)			// duan lu qi shi fou zai xian
		{
				for(int i = 0; i < Output_ChN_default;i++)
				{
					AC3PPDU_RL_time[i + CH1_out].LT_state &=0xffffff7e;
					orderFlag[i]=true;
				}
		}	
	#endif
			
#endif
#if (SUPPORT_ZERO_LINE  && SUPPORT_RELAY_CTRL)
			if(orderFlag_N)
			{
				RL_N_now_state = AC3PPDU_RL_N_time.LT_state  & 0x00000001 ;
				RL_N_last_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr] & 0x00000001;
				if(RL_N_now_state != RL_N_last_state)
				{
					if(RL_N_now_state > 0)
					{
						RL_N_ON_flag = 1;
						RL_N_OFF_flag = 0;
						if((AC3PPDU_RL_N_time.LT_state & 0x40) > 0)
						{
							RL_N_delay_Limit = AC3PPDU_RL_N_time.RL_ontime *1000;
							RL_N_begin_delay_flag = 1;
							RL_N_end_delay_flag = 0;
						}else
						{
							RL_N_delay_Limit = 0;
							RL_N_begin_delay_flag = 0;
							RL_N_end_delay_flag = 1;						
						}
					}else
					{
						RL_N_ON_flag = 0;
						RL_N_OFF_flag = 1;
						if((AC3PPDU_RL_N_time.LT_state & 0x80) > 0)
						{
							RL_N_delay_Limit = AC3PPDU_RL_N_time.RL_offtime *1000;
							RL_N_begin_delay_flag = 1;
							RL_N_end_delay_flag = 0;
						}else
						{
							RL_N_delay_Limit = 0;
							RL_N_begin_delay_flag = 0;
							RL_N_end_delay_flag = 1;						
						}						
					}
				}else
				{
						RL_N_delay_Limit = 0;
						RL_N_begin_delay_flag = 0;
						RL_N_end_delay_flag = 0;
						RL_N_ON_flag = 0;
						RL_N_OFF_flag = 0;					
				}
				orderFlag_N = false;
				AC3PPDU_RL_N_time.LT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr];
			}
#endif

			for(int k = 0;k < Output_ChN_default;k++)
			{
				if(orderFlag[k])
				{
				RL_now_state[k] 	= AC3PPDU_RL_time[k + CH1_out].LT_state 							& 0x00000001;
				RL_last_state[k] 	= AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + k] 			& 0x00000001;
				if(RL_now_state[k] != RL_last_state[k])
				{
					if(RL_now_state[k] > 0)
					{
						RL_ON_flag[k] 	= 1;
						RL_OFF_flag[k] 	= 0;
						if((AC3PPDU_RL_time[k + CH1_out].LT_state & 0x40) > 0)//有延时
						{
							RL_delay_Limit[k] = AC3PPDU_RL_time[k + CH1_out].RL_ontime * 1000;//秒转成毫秒
							RL_begin_delay_flag[k] = 1;
							RL_end_delay_flag[k] = 0;
						}else//无延时
						{
							RL_begin_delay_flag[k] = 0;
							RL_end_delay_flag[k] = 1;
							RL_delay_Limit[k] = 0;
						}								
					}else
					{
						RL_OFF_flag[k] = 1;
						RL_ON_flag[k] = 0;
						if((AC3PPDU_RL_time[k + CH1_out].LT_state & 0x80) > 0)//有延时
						{
							RL_begin_delay_flag[k] 	= 1;
							RL_end_delay_flag[k] 		= 0;
							RL_delay_Limit[k] 			= AC3PPDU_RL_time[k + CH1_out].RL_offtime * 1000;//秒转成毫秒
						}else//无延时
						{
							RL_begin_delay_flag[k] = 0;
							RL_end_delay_flag[k] = 1;
						}				
					}
				}
				else{
						RL_delay_Limit[k] = 0;
						RL_begin_delay_flag[k] = 0;
						RL_end_delay_flag[k] = 0;
						RL_ON_flag[k] = 0;
						RL_OFF_flag[k] = 0;
					
				}
				}
				orderFlag[k]=false;
				AC3PPDU_RL_time[k + CH1_out].LT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + k];
			}
#if SUPPORT_ZERO_LINE			
			if(RL_N_end_delay_flag > 0)
			{
				RL_N_end_delay_flag = 0;
				RL_N_begin_delay_flag = 0;
				if(RL_N_ON_flag > 0)
				{
					RL_N_ON_flag = 0;
					DB_Out4_H;
					AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr] = (AC3PPDU_RL_N_time.FT_state | 0x00000001);
				}else if(RL_N_OFF_flag > 0)
				{
					RL_N_OFF_flag = 0;
					DB_Out4_L;
					AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr] = (AC3PPDU_RL_N_time.FT_state & 0xfffffffe);
				}else
				{
					;
				}
				BUFF_Data;
				LOCK_Data;
			}
#endif			
			for(int i = 0;i < Output_ChN_default;i++)
			{
				if(RL_end_delay_flag[i] > 0)
				{
					RL_begin_delay_flag[i] 	= 0;
					RL_end_delay_flag[i] 		= 0;
					if(RL_ON_flag[i] > 0)
					{
						RL_ON_flag[i] = 0;
						switch (i)
						{
							case 0:
								DB_Out1_H;
								break;
							case 1:
								DB_Out2_H;
								break;
							case 2:
								DB_Out3_H;
								break;
							default:
								return;
						}
						AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + i] = (AC3PPDU_RL_time[i + CH1_out].LT_state 				| 0x01);
						AC3PPDU_Modbus_Reg[Mb_Dbuff_OUTCH1_ST_Addr + (i % 3)] = AC3PPDU_RL_time[i + CH1_out].LT_state | 0x00000001;
						
					}else if(RL_OFF_flag[i] > 0)
					{
						RL_OFF_flag[i] = 0;
						switch (i)
						{
							case 0:
								DB_Out1_L;
								break;
							case 1:
								DB_Out2_L;
								break;
							case 2:
								DB_Out3_L;
								break;
							default:
								return;
						}
						AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + i]  = (AC3PPDU_RL_time[i + CH1_out].LT_state & 0xfffffffe);
						AC3PPDU_Modbus_Reg[Mb_Dbuff_OUTCH1_ST_Addr + (i % 3)]  = AC3PPDU_RL_time[i + CH1_out].LT_state & 0xfffffffe;					
					}else
					{
						;
					}
				}

				BUFF_Data;
				//DelayNms(5);
				LOCK_Data;
			}
			RL_Allon_flag = false;
			RL_Alloff_flag = false;		
	}
#endif
}

static void LimiT_enable_check(uint8_t ch_x,uint32_t Lt_v)
{
	uint16_t temp0 = 0;
	temp0 = Lt_v >> 1;
	if(ch_x > 3)
	{
		return;
	}
	//通道最大电压
	if((temp0 & AC3PPDU_Vmax_LT_enable) == AC3PPDU_Vmax_LT_enable)
	{
		AC3PPDU_Vmax_LTen_flag[ch_x] = 1;
	}
	else
	{
		AC3PPDU_Vmax_LTen_flag[ch_x] = 0;
	}
	//最小电压
	if((temp0 & AC3PPDU_Vmin_LT_enable) == AC3PPDU_Vmin_LT_enable)
	{
		AC3PPDU_Vmin_LTen_flag[ch_x] = 1;
	}
	else
	{
		AC3PPDU_Vmin_LTen_flag[ch_x] = 0;
	}
	//最大电流
	if((temp0 & AC3PPDU_Imax_LT_enable) == AC3PPDU_Imax_LT_enable)
	{
		AC3PPDU_Imax_LTen_flag[ch_x] = 1;
	}
	else
	{
		AC3PPDU_Imax_LTen_flag[ch_x] = 0;
	}
	//最大功率
	if((temp0 & AC3PPDU_Wmax_LT_enable) == AC3PPDU_Wmax_LT_enable)
	{
		AC3PPDU_Wmax_LTen_flag[ch_x] = 1;
	}
	else
	{
		AC3PPDU_Wmax_LTen_flag[ch_x] = 0;
	}
	//最大电量
	if((temp0 & AC3PPDU_kWhmax_LT_enable) == AC3PPDU_kWhmax_LT_enable)
	{
		AC3PPDU_kWhmax_LTen_flag[ch_x] = 1;
	}
	else
	{
		AC3PPDU_kWhmax_LTen_flag[ch_x] = 0;
	}
}
static void check_3_phse()
{
	uint8_t Phase_3_Close_flag=0;
	
	if(3 == Phase_N){
		for(int i = 0 ; i < Output_ChN_default; i += 3 )
		{
			Phase_3_Close_flag = 0;
			for(int j = 1;j <= 3;j++)
			{
				if(RL_Func_statu[j+i] == 1)
				{
					Phase_3_Close_flag = 1;
					break;
				}
			}
			if(Phase_3_Close_flag)
			{
				for(int j = 1;j <= 3;j++)
				{
					RL_Func_statu[j+i] = 1;
				}
			}
			Phase_3_Close_flag = 0;
		}
	}
}


static void RL_Over_Func()
{
	
	//check_3_phse();
	
	if(RL_All_Func)
	{

		for(int i = 0; i < Output_ChN_default;i++)
		{
			AC3PPDU_RL_time[i + CH1_out].LT_state = AC3PPDU_RL_time[i + CH1_out].LT_state &0xffffff3e;
			orderFlag[i]=true;
			//orderFlag_N = true;
		}
		RL_All_Func = 0;

		return;
	}
	for(int i = 0; i < Output_ChN_default;i++)
	{
		if(RL_Func_statu[i+1])
		{
			AC3PPDU_RL_time[i + CH1_out].LT_state = AC3PPDU_RL_time[i + CH1_out].LT_state &0xffffff3e;
			orderFlag[i]=true;

			RL_Func_statu[i+1] = 0;
		}
	}
}

static void key_io_control()
{

	if(detection_value == true)
	{
		AC3PPDU_Modbus_Reg[Mb_Dbuff_Detection] = 0x1;
	}else
	{
		AC3PPDU_Modbus_Reg[Mb_Dbuff_Detection] = 0x0;
	}
}

int main(void)
{
	app_init(&meta_data);
	InitSysTick();
	InitLED();
	InitKey();
	InitTimer();
	InitRelay();
	Init_74hc573();
	InitAT24Cxx();
	InitUART1(9600);
	InitCH448F();
	AC3PPDU_SlaveAddress = ReadKeyValue();
	eMBInit(MB_RTU, AC3PPDU_SlaveAddress, 0, 115200, MB_PAR_NONE);
	eMBEnable();
	
	key_io_init(NULL);
	
	
	AC3PPDU_active_chn = Output_ChN_default;
	for(int i = 1; i <= AC3PPDU_active_chn;i++)
	{
		hlw8110_init(i);
	}
	
	
	ReadEeprom();
	strcpy(infomation.date,__DATE__);
	strcat(infomation.date," ");
	strcat(infomation.date,__TIME__);
	strcpy(infomation.ver,VERSION);
	int size = sizeof(infomation);
	Devid_IDChalNum = AC3PPDU_Device_ID;
	Devid_IDChalNum = Devid_IDChalNum << 8;
	Devid_IDChalNum += Output_ChN_default;
	AC3PPDU_Modbus_Reg[Mb_Dbuff_DevAddr] = Devid_IDChalNum;
	infomation.channels = Output_ChN_default;
	flash_get_infomation(&infomation);
	
	
	AC3PPDU_RL_time[CH_in].LT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_LT_ST_Addr];
	AC3PPDU_RL_time[CH_in].FT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr];
	LimiT_enable_check(CH_in,AC3PPDU_RL_time[CH_in].LT_state);
	Enable_74hc573_Output;
	//	Fault_state_Last = Fault_state_Reg;
	
	AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] = AC3PPDU_APlack_Fault + AC3PPDU_BPlack_Fault;
	AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] += AC3PPDU_CPlack_Fault;
	
	for(int i = 0;i < Output_ChN_default;i++)
	{
		RL_last_state[i] = 0;
		AC3PPDU_RL_time[i + CH1_out].LT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + i];
		AC3PPDU_Modbus_Reg[Mb_Dbuff_CH1LT_ST_Addr + i] &= 0xfffffffe;
		AC3PPDU_RL_time[i + CH1_out].RL_ontime = AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Ton1_Addr + i];
		AC3PPDU_RL_time[i + CH1_out].RL_offtime = AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Toff1_Addr + i];
		LimiT_enable_check((i + CH1_out),AC3PPDU_RL_time[i + CH1_out].LT_state);
		orderFlag[i]=true;
	}
#if SUPPORT_ZERO_LINE
	RL_N_last_state = 0;
	AC3PPDU_RL_N_time.LT_state = AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr];					// add by liyi
	AC3PPDU_Modbus_Reg[Mb_Dbuff_CHNLT_ST_Addr] &= 0xfffffffe;
	AC3PPDU_RL_N_time.RL_offtime = AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_ToffN_Addr];				// add by liyi
	AC3PPDU_RL_N_time.RL_ontime = AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_TonN_Addr];					// add by liyi
#endif
	orderFlag_N = true;

	
	
	Fwdgt_Init();
#if SUPPORT_DETECTION
	detection_value = get_detection();
#endif
	
	uint32_t count = 0;
	while(1)
	{
//		CHK_JLINK();
#if SUPPORT_RELAY_CTRL
		check_jlink();
#endif
		eMBPoll();
		Fwdgt_reload();
		if(flash_flag == 1){
			LEDFlicker2();
			flash_flag = 0;
#if SUPPORT_DETECTION
			detection_value = get_detection();
#endif
			for(int j = 0 ; j < Hlw8110_CS;j++)
				read_Hlw8110(j,0);
			count ++;
			normal_running_time+=2;
		}
		
		if(count == 120)			// 120 second recode
		{
			count = 0;
			for(int i = 0; i < Output_ChN_default ;i++)
			{
				int temp = i << 2;
				Eeprom_Rbuf[ERom_TotalWh1_Addr+temp+0] = AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr+i] >> 24;
				Eeprom_Rbuf[ERom_TotalWh1_Addr+temp+1] = AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr+i] >> 16;
				Eeprom_Rbuf[ERom_TotalWh1_Addr+temp+2] = AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr+i] >> 8;
				Eeprom_Rbuf[ERom_TotalWh1_Addr+temp+3] = AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr+i];
			}
			AT24CxxWrite(ERom_TotalWh1_Addr,(Eeprom_Rbuf + ERom_TotalWh1_Addr),4*Output_ChN_default);
		}
		
		AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] = AC3PPDU_Output[CH1_out].AC_V;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] = AC3PPDU_Output[CH2_out].AC_V;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr] = AC3PPDU_Output[CH3_out].AC_V;
		
		AC3PPDU_Modbus_Reg[Mb_Dbuff_IAP_Addr] = AC3PPDU_Output[CH1_out].AC_I;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_IBP_Addr] = AC3PPDU_Output[CH2_out].AC_I;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_ICP_Addr] = AC3PPDU_Output[CH3_out].AC_I;
		
		AC3PPDU_Modbus_Reg[Mb_Dbuff_WAP_Addr] = AC3PPDU_Output[CH1_out].AC_P;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_WBP_Addr] = AC3PPDU_Output[CH2_out].AC_P;
		AC3PPDU_Modbus_Reg[Mb_Dbuff_WCP_Addr] = AC3PPDU_Output[CH3_out].AC_P;
		
		AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr] = hlw8110_base[CH1_out] + (hlw8110_store[CH1_out]*1000);
		AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhBP_Addr] =	hlw8110_base[CH2_out] + (hlw8110_store[CH2_out]*1000);
		AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhCP_Addr] = hlw8110_base[CH3_out] + (hlw8110_store[CH3_out]*1000);
		for(int i = 0;i < (Output_ChN_default + 1);i++)
		{
			Fault_state_process(i);
		}
#if SUPPORT_RELAY_CTRL
		RL_Over_Func();
#endif
		MODbus_CMD_New();
	}
}


static void MODbus_CMD_New(void)
{
	if(Modbus_Wr_buff[Wr_eeprom_cnt][0] > 0)
	{
		uint8_t i = 0;
		uint32_t temp_addr;
		uint32_t base_addr = Modbus_Wr_buff[Wr_eeprom_cnt][1];
		uint32_t data = Modbus_Wr_buff[Wr_eeprom_cnt][2];
		uint32_t value = 0;
		
		switch(base_addr)
		{
			case Mb_Dbuff_ViLit_max_Addr ... Mb_Dbuff_kWhiLit_max_Addr:						//input votage max votage min current power coustermer add by liyi
				{
					temp_addr = base_addr - Mb_Dbuff_ViLit_max_Addr;
					temp_addr = temp_addr << 2;
					temp_addr += ERom_ViLit_max_Addr;
					Eeprom_Rbuf[temp_addr + 0] = data >> 24;
					Eeprom_Rbuf[temp_addr + 1] = data >> 16;
					Eeprom_Rbuf[temp_addr + 2] = data >> 8;
					Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
					AC3PPDU_Modbus_Reg[base_addr] = data;
					AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
				}
				break;
			case Mb_Dbuff_VLit1_max_Addr ... Mb_Dbuff_VLit9_max_Addr:							//output voltage max threod for 1,2,3,4,5,6,7,8,9 channels
				{
					temp_addr = base_addr - Mb_Dbuff_VLit1_max_Addr;
					value = temp_addr;
					temp_addr = temp_addr << 2;
					temp_addr += ERom_VLit1_max_Addr;
					Eeprom_Rbuf[temp_addr + 0] = data >> 24;
					Eeprom_Rbuf[temp_addr + 1] = data >> 16;
					Eeprom_Rbuf[temp_addr + 2] = data >> 8;
					Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
					AC3PPDU_Modbus_Reg[base_addr] = data;
					if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
					{
						AC3PPDU_RL_time[value + CH1_out].LT_state &= (Shield_Vmax_Threshould_Disable);
						LimiT_enable_check((value + CH1_out),AC3PPDU_RL_time[value + CH1_out].LT_state);
					}
					AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
				}
				break;
			case Mb_Dbuff_VLit1_min_Addr ... Mb_Dbuff_VLit9_min_Addr:							//output voltage min thred for 1,2,3,4,5,6,7,8,9 channels
			{
					temp_addr = base_addr - Mb_Dbuff_VLit1_min_Addr;
					value = temp_addr;
					temp_addr = temp_addr << 2;
					temp_addr += ERom_VLit1_min_Addr;
					Eeprom_Rbuf[temp_addr + 0] = data >> 24;
					Eeprom_Rbuf[temp_addr + 1] = data >> 16;
					Eeprom_Rbuf[temp_addr + 2] = data >> 8;
					Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
					AC3PPDU_Modbus_Reg[base_addr] = data;
					if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
					{
						AC3PPDU_RL_time[value + CH1_out].LT_state &= (Shield_Vmin_Threshould_Disable);
						LimiT_enable_check((value + CH1_out),AC3PPDU_RL_time[value + CH1_out].LT_state);
					}
					AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
			}
				break;
			case Mb_Dbuff_ILit1_max_Addr ... Mb_Dbuff_ILit9_max_Addr:							// output current max throud for 1,2,3,4,5,6,7,8,9 channels
			{
					temp_addr = base_addr - Mb_Dbuff_ILit1_max_Addr;
					value = temp_addr;
					temp_addr = temp_addr << 2;
					temp_addr += ERom_ILit1_max_Addr;
					Eeprom_Rbuf[temp_addr + 0] = data >> 24;
					Eeprom_Rbuf[temp_addr + 1] = data >> 16;
					Eeprom_Rbuf[temp_addr + 2] = data >> 8;
					Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
					AC3PPDU_Modbus_Reg[base_addr] = data;
					if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
					{
						AC3PPDU_RL_time[value + CH1_out].LT_state &= (Shield_Imax_Threshould_Disable);
						LimiT_enable_check((value + CH1_out),AC3PPDU_RL_time[value + CH1_out].LT_state);
					}
					AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
			}
				break;
			case Mb_Dbuff_WLit1_max_Addr ... Mb_Dbuff_WLit9_max_Addr:							//output power max .....
			{
					temp_addr = base_addr - Mb_Dbuff_WLit1_max_Addr;
					value = temp_addr;
					temp_addr = temp_addr << 2;
					temp_addr += ERom_WLit1_max_Addr;
					Eeprom_Rbuf[temp_addr + 0] = data >> 24;
					Eeprom_Rbuf[temp_addr + 1] = data >> 16;
					Eeprom_Rbuf[temp_addr + 2] = data >> 8;
					Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
					AC3PPDU_Modbus_Reg[base_addr] = data;
					if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
					{
						AC3PPDU_RL_time[value + CH1_out].LT_state &= (Shield_Wmax_Threshould_Disable);
						LimiT_enable_check((value + CH1_out),AC3PPDU_RL_time[value + CH1_out].LT_state);
					}
					AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
			}
				break;
			case Mb_Dbuff_kWhLit1_max_Addr ... Mb_Dbuff_kWhLit9_max_Addr:					//output customers max .....
			{
						temp_addr = base_addr - Mb_Dbuff_kWhLit1_max_Addr;
						value = temp_addr;
						temp_addr = temp_addr << 2;
						temp_addr += ERom_kWhLit1_max_Addr;
						Eeprom_Rbuf[temp_addr + 0] = data >> 24;
						Eeprom_Rbuf[temp_addr + 1] = data >> 16;
						Eeprom_Rbuf[temp_addr + 2] = data >> 8;
						Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
						AC3PPDU_Modbus_Reg[base_addr] = data;
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_RL_time[value + CH1_out].LT_state &= (Shield_Kwhmax_Threshould_Disable);
							LimiT_enable_check((value + CH1_out),AC3PPDU_RL_time[value + CH1_out].LT_state);
						}
				
						AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
			}
				break;
			case Mb_Dbuff_RL_Allon_Addr:																					//relay all on
			{
				RL_Allon_flag = true;
				for(i = 0;i < Output_ChN_default;i++)
				{
					temp_addr = i << 1; 
					Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] = Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] | 0x41;
					AC3PPDU_RL_time[i + CH1_out].LT_state = Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr];
				}		
				AT24CxxWrite(ERom_CH1LT_ST_Addr,(Eeprom_Rbuf + ERom_CH1LT_ST_Addr),(2*Output_ChN_default));
				Eeprom_Rbuf[ERom_CHNLT_ST_Addr] = Eeprom_Rbuf[ERom_CHNLT_ST_Addr] | 0x41;
				AC3PPDU_RL_N_time.LT_state = Eeprom_Rbuf[ERom_CHNLT_ST_Addr];
				AT24CxxWrite(ERom_CHNLT_ST_Addr,(Eeprom_Rbuf + ERom_CHNLT_ST_Addr),2);
			}
				break;
			case Mb_Dbuff_RL_Alloff_Addr:																					//relay all off
			{
				RL_Alloff_flag = true;
				for(i = 0;i < Output_ChN_default;i++)
				{
					temp_addr = i << 1;
					Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] = Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] | 0x80;
					Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] = Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr] & 0xfe;
					AC3PPDU_RL_time[i + CH1_out].LT_state = Eeprom_Rbuf[ERom_CH1LT_ST_Addr + temp_addr];
				}
				AT24CxxWrite(ERom_CH1LT_ST_Addr,(Eeprom_Rbuf + ERom_CH1LT_ST_Addr),(2*Output_ChN_default));
				Eeprom_Rbuf[ERom_CHNLT_ST_Addr] = Eeprom_Rbuf[ERom_CHNLT_ST_Addr] | 0x80;
				Eeprom_Rbuf[ERom_CHNLT_ST_Addr] = Eeprom_Rbuf[ERom_CHNLT_ST_Addr] & 0xfe;
				AC3PPDU_RL_N_time.LT_state = Eeprom_Rbuf[ERom_CHNLT_ST_Addr];
				AT24CxxWrite(ERom_CHNLT_ST_Addr,(Eeprom_Rbuf + ERom_CHNLT_ST_Addr),2);
			}
				break;

			case Mb_Dbuff_LT_ST_Addr:																							//set input status
			{
				AC3PPDU_RL_time[CH_in].LT_state = data;
				Eeprom_Rbuf[ERom_LT_ST_Addr] = data;
				AC3PPDU_Modbus_Reg[base_addr] = data;
				AT24CxxWriteOneByte(ERom_LT_ST_Addr,Eeprom_Rbuf[ERom_LT_ST_Addr]);
				LimiT_enable_check(CH_in,AC3PPDU_RL_time[CH_in].LT_state);
			}
				break;
			case Mb_Dbuff_CH1LT_ST_Addr ...  Mb_Dbuff_CHNLT_ST_Addr:							//set output relay statues
			{
				temp_addr = base_addr - Mb_Dbuff_CH1LT_ST_Addr;
				if(temp_addr == 9) {					//Ch N
					AC3PPDU_RL_N_time.LT_state = data;
					orderFlag_N = true;
				}else{
					if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
					{
						data &= (Shield_Vmax_Threshould_Disable);
					}
					if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_min_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
					{
						data &= (Shield_Vmin_Threshould_Disable);
					}
					if(AC3PPDU_Modbus_Reg[Mb_Dbuff_ILit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
					{
						data &= (Shield_Imax_Threshould_Disable);
					}
					if(AC3PPDU_Modbus_Reg[Mb_Dbuff_WLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
					{
						data &= (Shield_Wmax_Threshould_Disable);
					}
					if(AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
					{
						data &= (Shield_Kwhmax_Threshould_Disable);
					}
					orderFlag[temp_addr]=true;
					AC3PPDU_RL_time[temp_addr + CH1_out].LT_state = data;
					
					LimiT_enable_check((temp_addr + CH1_out),AC3PPDU_RL_time[temp_addr + CH1_out].LT_state);
				}
				temp_addr = temp_addr << 1;
				temp_addr += ERom_CH1LT_ST_Addr;
				Eeprom_Rbuf[temp_addr] = data;
				AT24CxxWriteOneByte(temp_addr,Eeprom_Rbuf[temp_addr]);
			}
				break;
			case Mb_Dbuff_OUTCH1_ST_Addr ... Mb_Dbuff_OUTCH3_ST_Addr:							//set output channel relay's status
			{
				temp_addr = base_addr - Mb_Dbuff_OUTCH1_ST_Addr;
				//OutUnit_control_flag[temp_addr] = 1;
				temp_addr *= 3;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
				{
					data &= (Shield_Vmax_Threshould_Disable);
				}
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_min_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
				{
					data &= (Shield_Vmin_Threshould_Disable);
				}
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_ILit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
				{
					data &= (Shield_Imax_Threshould_Disable);
				}
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_WLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
				{
					data &= (Shield_Wmax_Threshould_Disable);
				}
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhLit1_max_Addr + temp_addr] <= THRESHOULD_JUDGMENT)
				{
					data &= (Shield_Kwhmax_Threshould_Disable);
				}
				for(int i=0;i<Output_ChN_default;i++)
				{
					orderFlag[i]=true;
				}
				AC3PPDU_RL_time[temp_addr + CH1_out].LT_state = data;
				AC3PPDU_RL_time[temp_addr + CH2_out].LT_state = data;
				AC3PPDU_RL_time[temp_addr + CH3_out].LT_state = data;
				
				LimiT_enable_check((temp_addr + CH1_out),AC3PPDU_RL_time[temp_addr + CH1_out].LT_state);
				LimiT_enable_check((temp_addr + CH2_out),AC3PPDU_RL_time[temp_addr + CH2_out].LT_state);
				LimiT_enable_check((temp_addr + CH3_out),AC3PPDU_RL_time[temp_addr + CH3_out].LT_state);
				
				temp_addr = temp_addr << 1;
				Eeprom_Rbuf[temp_addr + ERom_CH1LT_ST_Addr] = data;
				Eeprom_Rbuf[temp_addr + ERom_CH2LT_ST_Addr] = data;
				Eeprom_Rbuf[temp_addr + ERom_CH3LT_ST_Addr] = data;
				
				AT24CxxWriteOneByte(temp_addr + ERom_CH1LT_ST_Addr,Eeprom_Rbuf[temp_addr + ERom_CH1LT_ST_Addr]);
				AT24CxxWriteOneByte(temp_addr + ERom_CH2LT_ST_Addr,Eeprom_Rbuf[temp_addr + ERom_CH2LT_ST_Addr]);
				AT24CxxWriteOneByte(temp_addr + ERom_CH3LT_ST_Addr,Eeprom_Rbuf[temp_addr + ERom_CH3LT_ST_Addr]);
				
			}
				break;
			case Mb_Dbuff_RL_Ton1_Addr ... Mb_Dbuff_RL_TonN_Addr:									//set on status delay for 1,2,3,4,5,6,7,8,9,N channels
			{
				temp_addr = base_addr - Mb_Dbuff_RL_Ton1_Addr;
				if(temp_addr == 9){				//Ch   N   add by liyi
					AC3PPDU_RL_N_time.RL_ontime = data;
				}else
				{
					AC3PPDU_RL_time[temp_addr + CH1_out].RL_ontime = data;
				}
				AC3PPDU_RL_N_time.RL_ontime = data;
				temp_addr += ERom_RL_Ton1_Addr;
				Eeprom_Rbuf[temp_addr] = data;
				Eeprom_Rbuf[ERom_RL_TonN_Addr] = data;
				
				AC3PPDU_Modbus_Reg[base_addr] = Eeprom_Rbuf[temp_addr];
				AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_TonN_Addr] = Eeprom_Rbuf[ERom_RL_TonN_Addr];
				
				AT24CxxWriteOneByte(temp_addr,Eeprom_Rbuf[temp_addr]);
				AT24CxxWriteOneByte(ERom_RL_TonN_Addr,Eeprom_Rbuf[ERom_RL_TonN_Addr]);
			}
				break;
			case Mb_Dbuff_RL_Toff1_Addr ... Mb_Dbuff_RL_ToffN_Addr:               //set off status delay for 1,2,3,4,5,6,7,8,9,N channels
			{
				temp_addr = base_addr - Mb_Dbuff_RL_Toff1_Addr;
				if(temp_addr == 9){
					AC3PPDU_RL_N_time.RL_offtime = data;
				}else {
					AC3PPDU_RL_time[temp_addr + CH1_out].RL_offtime = data;
				}
				AC3PPDU_RL_N_time.RL_offtime = data;
				temp_addr += ERom_RL_Toff1_Addr;
				
				Eeprom_Rbuf[temp_addr] = data;
				Eeprom_Rbuf[ERom_RL_ToffN_Addr] = data;
				
				AC3PPDU_Modbus_Reg[base_addr] = Eeprom_Rbuf[temp_addr];
				AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_ToffN_Addr] = Eeprom_Rbuf[ERom_RL_ToffN_Addr];
				
				AT24CxxWriteOneByte(temp_addr,Eeprom_Rbuf[temp_addr]);
				AT24CxxWriteOneByte(ERom_RL_ToffN_Addr,Eeprom_Rbuf[ERom_RL_ToffN_Addr]);
			}
				break;
			case Mb_Dbuff_RL_Over_Ch1_Func ... Mb_Dbuff_RL_Over_Ch9_Func:					//threod over limit operation
			{
				temp_addr = base_addr - Mb_Dbuff_RL_Over_Ch1_Func;
				temp_addr += ERom_RL_Over_Ch1_Addr;
				Eeprom_Rbuf[temp_addr] = data;
				AC3PPDU_Modbus_Reg[base_addr] = Eeprom_Rbuf[temp_addr];
				AT24CxxWriteOneByte(temp_addr,Eeprom_Rbuf[temp_addr]);
			}
				break;
			case Mb_Dbuff_Clear_Chn1_Consumer ... Mb_Dbuff_Clear_Chn9_Consumer:
			{
				if(data)
				{
					
					temp_addr = base_addr - Mb_Dbuff_Clear_Chn1_Consumer;
					hlw8110_base[temp_addr+CH1_out] = 0;
					hlw8110_store[temp_addr+CH1_out] = 0.0;
				}
			}
			case Mb_Dbuff_Clear_Chnall_Consumer:
			{
				if(data){
					for(i = 0; i < Output_ChN_default;i++)
					{
						hlw8110_base[i+CH1_out] = 0;
						hlw8110_store[i+CH1_out] = 0.0;
					}
				}
			}
			break;
			case Mb_Dbuff_All_ViLit_Max ... Mb_Dbuff_All_kWhiLit_Max:
			{
				temp_addr = base_addr - Mb_Dbuff_All_ViLit_Max;
				temp_addr = temp_addr << 2;
				temp_addr += ERom_VILit_All_max_Addr;
				Eeprom_Rbuf[temp_addr + 0] = data >> 24;
				Eeprom_Rbuf[temp_addr + 1] = data >> 16;
				Eeprom_Rbuf[temp_addr + 2] = data >> 8;
				Eeprom_Rbuf[temp_addr + 3] = data >> 0;	
				AC3PPDU_Modbus_Reg[base_addr] = data;
				AT24CxxWrite(temp_addr,(Eeprom_Rbuf + temp_addr),4);
				switch (base_addr - Mb_Dbuff_All_ViLit_Max)
				{
					case 0:
					{
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] &= (Shield_Vmax_Threshould_Disable);
						}else
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] |= (Shield_Vmax_Threshould_enable);
						}
					}
						break;
					case 1:
					{
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] &= (Shield_Vmin_Threshould_Disable);
						}else
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] |= (Shield_Vmin_Threshould_enable);
						}
					}
						break;
					case 2:
					{
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] &= (Shield_Imax_Threshould_Disable);
						}else
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] |= (Shield_Imax_Threshould_enable);
						}
					}
						break;
					case 3:
					{
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] &= (Shield_Wmax_Threshould_Disable);
						}else
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] |= (Shield_Wmax_Threshould_enable);
						}			
					}
						break;
					case 4:
					{
						if(AC3PPDU_Modbus_Reg[base_addr] <= THRESHOULD_JUDGMENT)
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] &= (Shield_Kwhmax_Threshould_Disable);
						}else
						{
							AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr] |= (Shield_kWhmax_Threshould_enable);
						}	
					}
						break;
				}
			}
			break;
			case Mb_Dbuff_All_OverFunc:
			{
				temp_addr = base_addr - Mb_Dbuff_All_OverFunc;
				temp_addr += Mb_Dbuff_All_OverFunc;
				Eeprom_Rbuf[temp_addr] = data;
				AC3PPDU_Modbus_Reg[base_addr] = Eeprom_Rbuf[temp_addr];
				AT24CxxWriteOneByte(temp_addr,Eeprom_Rbuf[temp_addr]);
			}
				break;
			case Mb_Dbuff_break_Addr:
			{
				break_2_boot_upgreade();
			}
			break;
			default:
				break;
		}
		Modbus_Wr_buff[Wr_eeprom_cnt][0] = 0;
		//Wr_eeprom_begin_flag = true;
	}
	Wr_eeprom_cnt++;
	if(Wr_eeprom_cnt >= Mb_Wcmd_Width)
	{
		Wr_eeprom_cnt = 0;
	}
}

//static void MODbus_CMD_New(void)
//{
//	if(Modbus_Wr_buff[Wr_eeprom_cnt][0] > 0)
//	{
//		uint8_t i = 0;
//		uint32_t temp_addr;
//		uint32_t base_addr = Modbus_Wr_buff[Wr_eeprom_cnt][1];
//		uint32_t data = Modbus_Wr_buff[Wr_eeprom_cnt][2];
//		uint32_t value = 0;
//		
//		switch(base_addr)
//		{
//			case Mb_Dbuff_RL_Allon_Addr:
//			{
//				DB_Out1_H;	
//				DB_Out2_H;
//				DB_Out3_H;
//				BUFF_Data;
//				LOCK_Data;
//			}				
//			break;
//			case Mb_Dbuff_RL_Alloff_Addr:	
//			{
//				DB_Out1_L;	
//				DB_Out2_L;
//				DB_Out3_L;	
//				BUFF_Data;
//				LOCK_Data;
//			}
//			break;
//		}
//		Modbus_Wr_buff[Wr_eeprom_cnt][0] = 0; 
//	}
//	Wr_eeprom_cnt++;
//	if(Wr_eeprom_cnt >= Mb_Wcmd_Width)
//	{
//		Wr_eeprom_cnt = 0;
//	}
//}
static void Fault_state_process(uint8_t ch_x)
{
	uint16_t i = 0;
	
	if(ch_x != CH_in)
		i = (ch_x -1)<< 3;
	
	
	if(ch_x == CH_in)
	{
		uint32_t sort_buff[3] = {0};
		uint32_t Vmax = 0;
		uint32_t Vmin = 0;
		sort_buff[0] = AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr];
		sort_buff[1] = AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr];
		sort_buff[2] = AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr];
		Vmax = (sort_buff[0] >= sort_buff[1]) ? sort_buff[0] :sort_buff[1];
		Vmax = (Vmax >= sort_buff[2]) ? Vmax : sort_buff[2];
		
		Vmin = (sort_buff[0] <= sort_buff[1]) ? sort_buff[0] :sort_buff[1];
		Vmin = (Vmin <= sort_buff[2]) ? Vmin : sort_buff[2];
		
		if((Vmin < AC3PPDU_Lack_Voltage) && (Vmax != 0) && (Vmax > (AC3PPDU_Lack_Voltage*2)))
		{
			uint32_t v_mid = AC3PPDU_Lack_Voltage *2; 
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] < v_mid)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackA_Addr] = 1;
			}
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] < v_mid)
			{
					AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackB_Addr] = 1;
			}
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] < v_mid)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackC_Addr] =1;
			}
		}else 
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackA_Addr] = 0;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackB_Addr] = 0;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_LackC_Addr] = 0;
		}
		
		if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr]  & Shield_Vmax_Threshould_enable) > 0)
		{
			if(AC_BASE[0] > AC3PPDU_Modbus_Reg[Mb_Dbuff_All_ViLit_Max])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_Vmax_Fault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Vmin_NFault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_All_OverFunc] & AC3PPDU_Over_V_Max_Func_enable)
				{
					RL_All_Func = 1;
				}
				
			}else if(AC_BASE[0] > AC3PPDU_Modbus_Reg[Mb_Dbuff_All_ViLit_Min])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Vmax_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Vmin_NFault;
			}else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Vmax_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_Vmin_Fault;
			}
		}
		
		if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr]  & Shield_Vmin_Threshould_enable) > 0)
		{
			if(AC_BASE[0] < AC3PPDU_Modbus_Reg[Mb_Dbuff_All_ViLit_Min])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_Vmin_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_All_OverFunc] & AC3PPDU_Over_V_Min_Func_enable)
				{
					RL_All_Func = 1;
				}
			}
			else//小于最小
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Vmin_NFault;
			}
		}
		
		if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr]  & Shield_Imax_Threshould_enable) > 0)
		{
			if(AC_BASE[1] > AC3PPDU_Modbus_Reg[Mb_Dbuff_All_IiLit_Max])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_Imax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_All_OverFunc] & AC3PPDU_Over_I_Max_Func_enable)
				{
					RL_All_Func = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Imax_NFault;
			}
		}
		
		if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr]  & Shield_Wmax_Threshould_enable) > 0)
		{
			if(AC_BASE[2] > AC3PPDU_Modbus_Reg[Mb_Dbuff_All_WiLit_Max])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_Wmax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_All_OverFunc] & AC3PPDU_Over_P_Max_Func_enable)
				{
					RL_All_Func = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_Wmax_NFault;
			}
		}
		
		if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ALL_LT_ST_Addr]  & Shield_kWhmax_Threshould_enable) > 0)
		{
			if(AC_BASE[3] > AC3PPDU_Modbus_Reg[Mb_Dbuff_All_kWhiLit_Max])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] |= AC3PPDU_kWhmax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_All_OverFunc] & AC3PPDU_Over_C_Max_Func_enable)
				{
					RL_All_Func = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_Tr_All_FT_ST_Addr] &= AC3PPDU_kWhmax_NFault;
			}
		}
		
		return;
	}
	////电压最大、最小、缺相阈值使能，进行判断
	if(AC3PPDU_Vmax_LTen_flag[ch_x] > 0)
	{
		if(ch_x > CH_in)//输出通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + i] > AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_max_Addr + ch_x-1])//大于最大
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_Vmax_Fault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmin_NFault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Over_Ch1_Func+ch_x-1] & (AC3PPDU_Over_V_Max_Func_enable))   //is or not open func
				{
					RL_Func_statu[ch_x] = 1;
				}
			}
			else if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + i] > AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_min_Addr + ch_x-1])//大于最小，小于最大，正常
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmax_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmin_NFault;
			}
			else//小于最小
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmax_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_Vmin_Fault;
			}
		}
		else//输入通道
		{
			//A相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_AVmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AVmax_NFault;
			}
			//B相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BVmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BVmax_NFault;
			}
			//C相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CVmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CVmax_NFault;
			}
			
		}
	}
	else
	{
		if(ch_x > CH_in)
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmax_NFault;
		}
		else
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AVmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BVmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CVmax_NFault;
		}
	}
	//最小电压
	if(AC3PPDU_Vmin_LTen_flag[ch_x] > 0)
	{
		if(ch_x > CH_in)//输出通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + i] < AC3PPDU_Modbus_Reg[Mb_Dbuff_VLit1_min_Addr + ch_x -1])//大于最大   revice by liyi max -> min 
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_Vmin_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Over_Ch1_Func + ch_x - 1] & (AC3PPDU_Over_V_Min_Func_enable))   //is or not open func add by liyi
				{
					RL_Func_statu[ch_x] = 1;
				}
			}
			else//小于最小
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmin_NFault;
			}
		}
		else//输入通道
		{
			//A相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_min_Addr])//
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_APlack_NFault;
			}
			else if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_AVmin_Fault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_APlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_APlack_Fault;
			}
			//B相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_min_Addr])//
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BPlack_NFault;
			}
			else if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BVmin_Fault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BPlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BPlack_Fault;
			}
			//C相
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ViLit_min_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CPlack_NFault;
			}
			else if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CVmin_Fault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CPlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CVmin_NFault;
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CPlack_Fault;
			}
			
		}
	}
	else
	{
		if(ch_x > CH_in)
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Vmin_NFault;
		}
		else
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AVmin_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BVmin_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CVmin_NFault;
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VAP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_APlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_APlack_Fault;
			}
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VBP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BPlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BPlack_Fault;
			}
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_VCP_Addr] > 1000)
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CPlack_NFault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CPlack_Fault;
			}
		}
	}
	//电流最大
	if(AC3PPDU_Imax_LTen_flag[ch_x] > 0)
	{
		if(ch_x > CH_in)//输出通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + 1 + i] > AC3PPDU_Modbus_Reg[Mb_Dbuff_ILit1_max_Addr + ch_x -1])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_Imax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Over_Ch1_Func + ch_x-1] & (AC3PPDU_Over_I_Max_Func_enable))   //is or not open func add by liyi
				{
					RL_Func_statu[ch_x] = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Imax_NFault;
			}
		}
		else//输入通道
		{
			if((AC3PPDU_Modbus_Reg[Mb_Dbuff_IAP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_IiLit_max_Addr]))//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_AImax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AImax_NFault;
			}
			
			if((AC3PPDU_Modbus_Reg[Mb_Dbuff_IBP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_IiLit_max_Addr]))//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BImax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BImax_NFault;
			}
			
			if((AC3PPDU_Modbus_Reg[Mb_Dbuff_ICP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_IiLit_max_Addr]))//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CImax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CImax_NFault;
			}
		}
	}
	else
	{
		if(ch_x > CH_in)
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Imax_NFault;
		}
		else
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AImax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BImax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CImax_NFault;
		}
	}
	//功率最大
	if(AC3PPDU_Wmax_LTen_flag[ch_x] > 0)
	{
		if(ch_x > CH_in)//输出通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + 2 + i] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WLit1_max_Addr + ch_x -1])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_Wmax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Over_Ch1_Func + ch_x-1] & (AC3PPDU_Over_P_Max_Func_enable))   //is or not open func add by liyi
				{
					RL_Func_statu[ch_x] = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Wmax_NFault;
			}
		}
		else//输入通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_WAP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_AWmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AWmax_NFault;
			}
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_WBP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BWmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BWmax_NFault;
			}
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_WCP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CWmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CWmax_NFault;
			}
		}
	}
	else
	{
		if(ch_x > CH_in)
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_Wmax_NFault;
		}
		else
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AWmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BWmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CWmax_NFault;
		}
	}
	//电量最大
	if(AC3PPDU_kWhmax_LTen_flag[ch_x] > 0)
	{
		if(ch_x > CH_in)//输出通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_Out1Para_Addr + 6 + i] > AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhLit1_max_Addr + ch_x-1])
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] |= AC3PPDU_kWhmax_Fault;
				if(AC3PPDU_Modbus_Reg[Mb_Dbuff_RL_Over_Ch1_Func + ch_x-1] & (AC3PPDU_Over_C_Max_Func_enable))   //is or not open func add by liyi
				{
					RL_Func_statu[ch_x] = 1;
				}
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_kWhmax_NFault;
			}
		}
		else//输入通道
		{
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhAP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_AkWhmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AkWhmax_NFault;
			}
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhBP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_BkWhmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BkWhmax_NFault;
			}
			
			if(AC3PPDU_Modbus_Reg[Mb_Dbuff_kWhCP_Addr] > AC3PPDU_Modbus_Reg[Mb_Dbuff_WiLit_max_Addr])//超限
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] |= AC3PPDU_CkWhmax_Fault;
			}
			else
			{
				AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CkWhmax_NFault;
			}
		}
	}
	else
	{
		if(ch_x > CH_in)
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr + ch_x] &= AC3PPDU_kWhmax_NFault;
		}
		else
		{
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_AkWhmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_BkWhmax_NFault;
			AC3PPDU_Modbus_Reg[Mb_Dbuff_FT_ST_Addr] &= AC3PPDU_CkWhmax_NFault;
		}
	}
}

#ifdef  USE_FULL_ASSERT
void assert_failed(uint8_t* file, uint32_t line) 
{ 
  while (1);
}
#else
void __aeabi_assert(const char * x1, const char * x2, int x3)
{
	(void)x3;
}
#endif