SmartPDCode/truing_control/STS/HARDWARE/R_Led/R_Led.c

/*********************************************************************************************************
* Module   : R_Led.c
* Abstract : R_Led module displays the relay status!
* Version  : 1.0.0
* Author   : Leopul(COPYRIGHT 2025 - 2027 Leopul. All rights reserved.)
* Complete : 2025-02-16
* Content  : None
* Note     : None
*********************************************************************************************************/

#include "R_Led.h"
#include "gd32f30x_libopt.h"
#include "Sn74lvc573.h"
#include "main.h"


#define POWER_R2_Y        GPIO_PIN_4
#define POWER_R2_G        GPIO_PIN_5
#define POWER_R2_R        GPIO_PIN_6

#define POWER_R1_Y        GPIO_PIN_1
#define POWER_R1_G        GPIO_PIN_2
#define POWER_R1_R        GPIO_PIN_3


#define POWER_OUT_R      	GPIO_PIN_14
#define POWER_OUT_G       GPIO_PIN_13
#define POWER_OUT_Y       GPIO_PIN_12







uint16_t led_status = 0;


void r_led_init(void)
{
	rcu_periph_clock_enable(RCU_GPIOD);  

	gpio_init(GPIOD,GPIO_MODE_OUT_PP,GPIO_OSPEED_50MHZ,POWER_R2_Y |POWER_R2_G| POWER_R2_R | POWER_R1_Y | POWER_R1_G | POWER_R1_R | POWER_OUT_R | POWER_OUT_G | POWER_OUT_Y);
	gpio_bit_reset(GPIOD, POWER_R2_Y |POWER_R2_G| POWER_R2_R | POWER_R1_Y | POWER_R1_G | POWER_R1_R | POWER_OUT_R | POWER_OUT_G | POWER_OUT_Y);	
	
}


void in_r_led_on_off(unsigned char channel)
{
//	if(channel  == 0)
//	{
//		gpio_bit_set(GPIOD, POWER_R1_G);
//		gpio_bit_reset(GPIOD, POWER_R2_G);
//	}else
//	{
//		gpio_bit_reset(GPIOD, POWER_R1_G);
//		gpio_bit_set(GPIOD, POWER_R2_G);
//	}
}

void out_r_led(unsigned char status)
{
//	if(status == 0)
//	{
//		gpio_bit_set(GPIOD, POWER_OUT_G);
//	}else
//	{
//		gpio_bit_reset(GPIOD, POWER_OUT_G);
//	}
}

void show_wanning_led(void)
{
	sts_data_t *data = get_sts();
	if(data)
	{
		uint16_t value = 0;
		if(data->m_data.input_status.input_status[0] && data->m_data.input_status.input_status[1])
		{
			if(data->m_data.input_wanning.waning[0] == 0 &&  data->m_data.input_wanning.waning[1] == 0)
			{
					if(data->m_data.md_choise.choise_ch == INPUT_CHANNEL_1)
					{
						value |= POWER_R1_G;
					}else
					{
						value |= POWER_R2_G;
					}
			}else
			{
				if(data->m_data.input_wanning.waning[0] != 0)
				{
					value |= POWER_R1_Y;
				}else
				{
					value |= POWER_R1_G;
				}
				if(data->m_data.input_wanning.waning[1] != 0)
				{
					value |= POWER_R2_Y;
				}else
				{
					value |= POWER_R2_G;
				}
			}

		}else
		{
			if(data->m_data.input_status.input_status[0] == 0)
			{
				value |=POWER_R1_R;
				if(data->m_data.input_status.input_status[1] == 1)
				{
					if(data->m_data.input_wanning.waning[1] != 0)
					{
						value |= POWER_R2_Y;
					}else
						value |= POWER_R2_G;
				
				}
				if(data->m_data.input_wanning.waning[0] != 0)
				{
					value |= POWER_R1_Y;
				}
			}
			if(data->m_data.input_status.input_status[1] == 0)
			{
				value |=POWER_R2_R;
				if(data->m_data.input_status.input_status[0] == 1)
				{
					if(data->m_data.input_wanning.waning[0] != 0)
					{
						value |= POWER_R1_Y;
					}else
						value |=POWER_R1_G;
				}
				if(data->m_data.input_wanning.waning[1] != 0)
				{
					value |= POWER_R2_Y;
				}				
			}
		}
		if(data->m_data.out_status == 1)
		{
			if(data->m_data.output_waning.waning != 0)
				value |= POWER_OUT_Y;
			else
				value |= POWER_OUT_G;
		}else
		{
			if(data->m_data.output_waning.waning != 0)
				value |= POWER_OUT_Y;
			value |= POWER_OUT_R;
		}
		
		if(value != led_status)
		{
			led_status = value;
			gpio_bit_reset(GPIOD, POWER_R2_Y |POWER_R2_G| POWER_R2_R | POWER_R1_Y | POWER_R1_G | POWER_R1_R | POWER_OUT_R | POWER_OUT_G | POWER_OUT_Y);	
			gpio_bit_set(GPIOD,led_status);
		}
	}
}