SmartPDCode/control/NEW_STS/HARDWARE/R_Led/R_Led.c

/*********************************************************************************************************
* Module   : R_Led.c
* Abstract : R_Led module displays the relay status!
* Version  : 1.0.0
* Author   : Leopul(COPYRIGHT 2025 - 2027 Leopul. All rights reserved.)
* Complete : 2025-02-16
* Content  : None
* Note     : None
*********************************************************************************************************/

#include "R_Led.h"
#include "gd32f30x_libopt.h"
#include "Sn74lvc573.h"
#include "main.h"


#define POWER_R2_Y        GPIO_PIN_12
#define POWER_R2_G        GPIO_PIN_11
#define POWER_R2_R        GPIO_PIN_10

#define POWER_R1_Y        GPIO_PIN_9
#define POWER_R1_G        GPIO_PIN_8
#define POWER_R1_R        GPIO_PIN_7


#define ALL_RUN           			((1 << 11) |  (1 << 8))

#define WANING_1_RUN_2    			((1 << 9)  | (1 << 11))

#define WANING_1_WANING_2 			((1 <<12)  | (1 << 10) | (1 << 9) | (1 << 7))

#define WANING_2_RUN_1          ((1 << 12) | (1 << 8))

#define CLEAR_LED               ((1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12))

uint16_t led_status = 0;


void r_led_init(void)
{
	rcu_periph_clock_enable(RCU_GPIOC);  
//	
//  gpio_mode_set(GPIOB, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN_2);          
//  gpio_output_options_set(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_2); 
//  gpio_bit_reset(GPIOB, GPIO_PIN_2);  

//  gpio_mode_set(GPIOB, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN_10);          
//  gpio_output_options_set(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_10); 
//  gpio_bit_reset(GPIOB, GPIO_PIN_10);

//  gpio_mode_set(GPIOB, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_PIN_11);          
//  gpio_output_options_set(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_11); 
//  gpio_bit_reset(GPIOB, GPIO_PIN_11);	
	
	gpio_init(GPIOC,GPIO_MODE_OUT_PP,GPIO_OSPEED_50MHZ,POWER_R2_Y |POWER_R2_G| POWER_R2_R | POWER_R1_Y | POWER_R1_G | POWER_R1_R);
	gpio_bit_reset(GPIOC, POWER_R2_Y |POWER_R2_G| POWER_R2_R | POWER_R1_Y | POWER_R1_G | POWER_R1_R);	
	
}


void in_r_led_on_off(unsigned char channel)
{
//	if(channel  == 0)
//	{
//		gpio_bit_set(GPIOB, GPIO_PIN_2);
//		gpio_bit_reset(GPIOB, GPIO_PIN_10);
//	}else
//	{
//		gpio_bit_reset(GPIOB, GPIO_PIN_2);
//		gpio_bit_set(GPIOB, GPIO_PIN_10);
//	}
}

void out_r_led(unsigned char status)
{
//	if(status == 0)
//	{
//		gpio_bit_set(GPIOB, GPIO_PIN_11);
//	}else
//	{
//		gpio_bit_reset(GPIOB, GPIO_PIN_11);
//	}
}

void show_wanning_led(void)
{
	sts_data_t *data = get_sts();
	uint16_t pre_status = led_status;
	if(data)
	{
		if(data->m_data.input_wanning.waning[0] == 0 &&  data->m_data.input_wanning.waning[1] == 0)
		{
			led_status = ALL_RUN;
			if(pre_status != led_status)
			{
				gpio_bit_reset(GPIOC,CLEAR_LED);
				gpio_bit_set(GPIOC,led_status);
				unlock();
				lock();
			}
		}else if(data->m_data.input_wanning.waning[0] == 0 && data->m_data.input_wanning.waning[1] > 0)
		{
			led_status = WANING_2_RUN_1;
			if(pre_status != led_status)
			{
				gpio_bit_reset(GPIOC,CLEAR_LED);
				gpio_bit_set(GPIOC,led_status);
				unlock();
				lock();
			}			
		}else if(data->m_data.input_wanning.waning[0] > 0 && data->m_data.input_wanning.waning[1] > 0)
		{
			led_status = WANING_1_WANING_2;
			if(pre_status != led_status)
			{
				gpio_bit_reset(GPIOC,CLEAR_LED);
				gpio_bit_set(GPIOC,led_status);
				unlock();
				lock();
			}				
		}else 
		{
			led_status = WANING_1_RUN_2;
			if(pre_status != led_status)
			{
				gpio_bit_reset(GPIOC,CLEAR_LED);
				gpio_bit_set(GPIOC,led_status);
				unlock();
				lock();
			}				
		}
	}
}