SmartPDCode/ip_conf_dts/dts/board.dts

/*
 * Allwinner Technology CO., Ltd.
 */

/dts-v1/;

 /* optee used 7MB: SHM 2M: OS: 1M: TA:4M*/
/memreserve/ 0x41B00000 0x00100000;
/* DSP used 1MB */
/*/memreserve/ 0x42000000 0x00100000;*/
#include "sun8iw20p1.dtsi"

/{
	model = "sun8iw20";
	compatible = "allwinner,r528", "arm,sun8iw20p1";

	reg_vdd_cpu: vdd-cpu {
		compatible = "sunxi-pwm-regulator";
		pwms = <&pwm 3 5000 0>;
		regulator-name = "vdd_cpu";
		regulator-min-microvolt = <810000>;
		regulator-max-microvolt = <1160000>;
		regulator-ramp-delay = <25>;
		regulator-always-on;
		regulator-boot-on;
		status = "okay";
	};

	reg_usb1_vbus: usb1-vbus {
		compatible = "regulator-fixed";
		regulator-name = "usb1-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		regulator-enable-ramp-delay = <1000>;
		gpio = <&pio PB 10 GPIO_ACTIVE_HIGH>;
		enable-active-high;
	};
	/*
	spi_gpio: spi_gpio {
		compatible = "spi-gpio";
		#address-cells = <0x1>;
        #size-cells = <0>;
		// miso-gpios = <&pio PE 3 1>;
		mosi-gpios = <&pio PD 12 1>;
		sck-gpios = <&pio  PD 11 1>;
		cs-gpios = <&pio   PD 10 1>;
		pinctrl-names = "default";
		num-chipselects = <1>;
		status = "okay";
		st7789v{
			status = "okay";
			compatible ="sitronix,st7789v";
			reg = <0>;
			spi-max-frequency = <32000000>;
			rotate = <90>;
			spi-cpol;
			spi-cpha;
			rgb;
			fps = <30>;
			buswidth = <8>;
			reset-gpios = <&pio PD 13 GPIO_ACTIVE_LOW>;
			dc-gpios = <&pio PD 14 GPIO_ACTIVE_LOW>;
			//led-gpios = <&pio PE 13 GPIO_ACTIVE_HIGH>;
			debug = <7>;
		};
	};
	*/

};

&cpu0 {
	cpu-supply = <&reg_vdd_cpu>;
};

&pio {
	lcd_dc: lcd_dc{
				allwinner,pins = "PD1"; 
			};
	lcd_rst: lcd_rst{
				allwinner,pins = "PD0"; 
			};
	led: led{
				allwinner,pins = "PE8"; 
			};

	moni_spi: moni_spi {
		pins = "PD13", "PD14", "PD10","PD11", "PD12";
		function = "gpio_out";
		drive-strength = <10>;
		bias-pull-up;
	};
	sdc0_pins_a: sdc0@0 {
		allwinner,pins = "PF0", "PF1", "PF2",
				 "PF3", "PF4", "PF5";
		allwinner,function = "sdc0";
		allwinner,muxsel = <2>;
		allwinner,drive = <3>;
		allwinner,pull = <1>;
		pins = "PF0", "PF1", "PF2",
		       "PF3", "PF4", "PF5";
		function = "sdc0";
		drive-strength = <30>;
		bias-pull-up;
		power-source = <3300>;
	};


	sdc0_pins_b: sdc0@1 {
		pins = "PF0", "PF1", "PF2",
		       "PF3", "PF4", "PF5";
		function = "sdc0";
		drive-strength = <30>;
		bias-pull-up;
		power-source = <1800>;
	};

	sdc0_pins_c: sdc0@2 {
		pins = "PF0", "PF1", "PF2",
			"PF3", "PF4", "PF5";
		function = "gpio_in";
	};

	/* TODO: add jtag pin */
	sdc0_pins_d: sdc0@3 {
		pins = "PF2", "PF4";
		function = "uart0";
		drive-strength = <10>;
		bias-pull-up;
	};

	sdc0_pins_e: sdc0@4 {
		pins = "PF0", "PF1", "PF3",
			"PF5";
		function = "jtag";
		drive-strength = <10>;
		bias-pull-up;
	};


	sdc1_pins_a: sdc1@0 {
		pins = "PG0", "PG1", "PG2",
		       "PG3", "PG4", "PG5";
		function = "sdc1";
		drive-strength = <30>;
		bias-pull-up;
	};

	sdc1_pins_b: sdc1@1 {
		pins = "PG0", "PG1", "PG2",
		       "PG3", "PG4", "PG5";
			function = "gpio_in";
	};

	sdc2_pins_a: sdc2@0 {
		allwinner,pins = "PC2", "PC3", "PC4",
				 "PC5", "PC6", "PC7";
		allwinner,function = "sdc2";
		allwinner,muxsel = <3>;
		allwinner,drive = <3>;
		allwinner,pull = <1>;
		pins = "PC2", "PC3", "PC4",
			"PC5", "PC6", "PC7";
		function = "sdc2";
		drive-strength = <30>;
		bias-pull-up;
	};

	sdc2_pins_b: sdc2@1 {
		pins = "PC2", "PC3", "PC4",
		       "PC5", "PC6", "PC7";
		function = "gpio_in";
	};

	wlan_pins_a:wlan@0 {
		pins = "PG11";
		function = "clk_fanout1";
	};

        uart0_pins_a: uart0_pins@0 {  /* For mangopi board */
                pins = "PE2", "PE3";
                function = "uart0";
                drive-strength = <10>;
                bias-pull-up;
        };

        uart0_pins_b: uart0_pins@1 {  /* For mangopi board */
                pins = "PE2", "PE3";
                function = "gpio_in";
        };

	uart1_pins_a: uart1_pins@0 {  /* For EVB1 board */
		pins = "PE11","PE10";
		allwinner,muxsel = <7>;
		function = "uart1";
		drive-strength = <10>;
		bias-pull-up;
	};

	uart1_pins_b: uart1_pins {  /* For EVB1 board */
		pins = "PE11","PE10";
		function = "gpio_in";
	};

	uart2_pins_a: uart2_pins@0 {  /* For EVB1 board */
		pins = "PC0", "PC1";
		function = "uart2";
		drive-strength = <10>;
		bias-pull-up;
	};

	uart2_pins_b: uart2_pins@1 {  /* For EVB1 board */
		pins = "PC0", "PC1";
		function = "gpio_in";
	};

	uart3_pins_a: uart3_pins@0 {  /* For bingpi-m2 board */
		pins = "PB6", "PB7";
		function = "uart3";
		allwinner,muxsel = <7>;
		drive-strength = <10>;
		bias-pull-up;
	};

	uart3_pins_b: uart3_pins@1 {  /* For bingpi-m2 board */
		pins = "PB6", "PB7";
		function = "gpio_in";
	};

	uart4_pins_a: uart4_pins@0 {  /* For bingpi-m2 board */
		pins = "PB2", "PB3";
		function = "uart4";
		allwinner,muxsel = <7>;
		drive-strength = <10>;
		bias-pull-up;
	};

	uart4_pins_b: uart4_pins@1 {  /* For bingpi-m2 board */
		pins = "PB2", "PB3";
		function = "gpio_in";
	};
	uart5_pins_a: uart5_pins@0 {  /* For bingpi-m2 board */
		pins = "PE6", "PE7";
		function = "uart5";
		allwinner,muxsel = <7>;
		drive-strength = <10>;
		bias-pull-up;
	};

	uart5_pins_b: uart5_pins@1 {  /* For bingpi-m2 board */
		pins = "PE6", "PE7";
		function = "gpio_in";
	};

	can0_pins_a: can0_pins@0 {
		pins = "PB2", "PB3";
		function = "can0";
		drive-strength = <10>;
		bias-pull-up;
	};

	can0_pins_b: can0_pins@1 {
		pins = "PB2", "PB3";
		function = "gpio_in";
	};

	can1_pins_a: can1_pins@0 {
		pins = "PB4", "PB5";
		function = "can1";
		drive-strength = <10>;
		bias-pull-up;
	};

	can1_pins_b: can1_pins@1 {
		pins = "PB4", "PB5";
		function = "gpio_in";
	};

	twi0_pins_a: twi0@0 {
		pins = "PB10", "PB11";	/*sck sda*/
		function = "twi0";
		drive-strength = <10>;
	};

	twi0_pins_b: twi0@1 {
		pins = "PB10", "PB11";
		function = "gpio_in";
	};

	twi1_pins_a: twi1@0 {
		pins = "PB4", "PB5";
		function = "twi1";
		drive-strength = <10>;
	};

	twi1_pins_b: twi1@1 {
		pins = "PB4", "PB5";
		function = "gpio_in";
	};

        twi2_pins_a: twi2@0 {
                pins = "PE12", "PE13";
                function = "twi2";
                drive-strength = <10>;
        };

        twi2_pins_b: twi2@1 {
                pins = "PE12", "PE13";
                function = "gpio_in";
        };

	twi3_pins_a: twi3@0 {
		pins = "PE6", "PE7";
		function = "twi3";
		drive-strength = <10>;
	};

	twi3_pins_b: twi3@1 {
		pins = "PE6", "PE7";
		function = "gpio_in";
	};

	gmac_pins_a: gmac@0 {
		pins = "PG0", "PG1", "PG2", "PG3",
		       "PG4", "PG5", "PG11",
		       "PG12","PG13", "PG14", "PG15";
		allwinner,function = "gmac0";
		allwinner,muxsel = <4>;
		allwinner,drive = <1>;
		allwinner,pull = <0>;
		drive-strength = <10>;
	};

	gmac_pins_b: gmac@1 {
		pins = "PG0", "PG1", "PG2", "PG3",
		       "PG4", "PG5", "PG11",
		       "PG12","PG13", "PG14", "PG15";
		allwinner,function = "gpio_in";
		allwinner,muxsel = <0>;
		allwinner,drive = <1>;
		allwinner,pull = <0>;
	};

	dmic_pins_a: dmic@0 {
		/* DMIC_PIN: CLK, DATA0, DATA1, DATA2, DATA3*/
		pins = "PB12", "PB11", "PB10", "PE14", "PB8";
		function = "dmic";
		drive-strength = <20>;
		bias-disable;
	};

	dmic_pins_b: dmic@1 {
		pins = "PB12", "PB11", "PB10", "PE14", "PB8";
		function = "io_disabled";
		drive-strength = <20>;
		bias-disable;
	};

	daudio0_pins_a: daudio0@0 {
		pins = "PE17", "PE16", "PE15", "PE14", "PE13";
		function = "i2s0";
		drive-strength = <20>;
		bias-disable;
	};

	daudio0_pins_b: daudio0_sleep@0 {
		pins = "PE17", "PE16", "PE15", "PE14", "PE13";
		function = "io_disabled";
		drive-strength = <20>;
		bias-disable;
	};

	daudio1_pins_a: daudio1@0 {
		pins = "PG11", "PG12", "PG13", "PG14", "PG15";
		function = "i2s1";
		drive-strength = <20>;
		bias-disable;
	};

	daudio1_pins_b: daudio1_sleep@0 {
		pins = "PG11", "PG12", "PG13", "PG14", "PG15";
		function = "io_disabled";
		drive-strength = <20>;
		bias-disable;
	};

	daudio2_pins_a: daudio2@0 {
		/* I2S_PIN: MCLK, BCLK, LRCK */
		pins = "PF6", "PF3", "PF5";
		function = "i2s2";
		drive-strength = <20>;
		bias-disable;
	};

	daudio2_pins_b: daudio2@1 {
		/* I2S_PIN: DOUT0 */
		pins = "PF1";
		function = "i2s2_dout";
		drive-strength = <20>;
		bias-disable;
	};

	daudio2_pins_c: daudio2@2 {
		/* I2S_PIN: DIN0 */
		pins = "PF0";
		function = "i2s2_din";
		drive-strength = <20>;
		bias-disable;
	};

	daudio2_pins_d: daudio2_sleep@0 {
		pins = "PF6", "PF3", "PF5", "PF1", "PF0";
		function = "io_disabled";
		drive-strength = <20>;
		bias-disable;
	};

	spdif_pins_a: spdif@0 {
		/* SPDIF_PIN: SPDIF_OUT */
		pins = "PG18";
		function = "spdif";
		drive-strength = <20>;
		bias-disable;
	};

	spdif_pins_b: spdif_sleep@0 {
		pins = "PG18";
		function = "io_disabled";
		drive-strength = <20>;
		bias-disable;
	};

	spi0_pins_a: spi0@0 {
		pins = "PC2", "PC4", "PC5"; /* clk, mosi, miso */
		function = "spi0";
		muxsel = <2>;
		drive-strength = <10>;
	};

	spi0_pins_b: spi0@1 {
		pins = "PC3", "PC7", "PC6";
		function = "spi0";
		muxsel = <2>;
		drive-strength = <10>;
		bias-pull-up;   /* cs, hold, wp should be pulled up */
	};

	spi0_pins_c: spi0@2 {
		pins = "PC2", "PC3", "PC4", "PC5","PC6", "PC7";
		function = "gpio_in";
		muxsel = <0>;
		drive-strength = <10>;
	};

	spi1_pins_a: spi1@0 {
		pins = "PD11", "PD12", "PD13"; /* clk, mosi, miso */
		function = "spi1";
		drive-strength = <10>;
	};

	spi1_pins_b: spi1@1 {
		pins = "PD10", "PD14", "PD15";
		function = "spi1";
		drive-strength = <10>;
		bias-pull-up;   /* cs, hold, wp should be pulled up */
	};

	spi1_pins_c: spi1@2 {
		pins = "PD10", "PD11", "PD12", "PD13","PD14", "PD15";
		function = "gpio_in";
		drive-strength = <10>;
	};

	ledc_pins_a: ledc@0 {
		pins = "PG7";
		function = "ledc";
		drive-strength = <10>;
	};

	ledc_pins_b: ledc@1 {
		pins = "PG7";
		function = "gpio_in";
	};

	pwm0_pin_a: pwm0@0 {
		pins = "PD16";
		function = "pwm0";
		drive-strength = <10>;
		bias-pull-up;
	};

	pwm0_pin_b: pwm0@1 {
		pins = "PD16";
		function = "gpio_in";
		bias-disable;
	};

	pwm2_pin_a: pwm2@0 {
		pins = "PD18";
		function = "pwm2";
		drive-strength = <10>;
		bias-pull-up;
	};

	pwm2_pin_b: pwm2@1 {
		pins = "PD18";
		function = "gpio_out";
	};

	pwm7_pin_a: pwm7@0 {
		pins = "PD22";
		function = "pwm7";
		drive-strength = <10>;
		bias-pull-up;
	};

	pwm7_pin_b: pwm7@1 {
		pins = "PD22";
		function = "gpio_in";
	};


	s_cir0_pins_a: s_cir@0 {
		pins = "PB7";
		function = "ir";
		drive-strength = <10>;
		bias-pull-up;
	};

	s_cir0_pins_b: s_cir@1 {
		pins = "PB7";
		function = "gpio_in";
	};

	ir1_pins_a: ir1@0 {
		pins = "PB0";
		function = "ir";
		drive-strength = <10>;
		bias-pull-up;
	};

	ir1_pins_b: ir1@1 {
		pins = "PB0";
		function = "gpio_in";
	};
};

&uart0 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart0_pins_a>;
	pinctrl-1 = <&uart0_pins_b>;
	status = "disabled";
};

&uart1 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart1_pins_a>;
	pinctrl-1 = <&uart1_pins_b>;
	status = "okay";
};

&uart2 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart2_pins_a>;
	pinctrl-1 = <&uart2_pins_b>;
	status = "disabled";
};

&uart3 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart3_pins_a>;
	pinctrl-1 = <&uart3_pins_b>;
	status = "okay";
};

&uart4 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart4_pins_a>;
	pinctrl-1 = <&uart4_pins_b>;
	status = "okay";
};

&uart5 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart5_pins_a>;
	pinctrl-1 = <&uart5_pins_b>;
	status = "okay";
};


&can0 {
	pinctrl-names = "default";
	pinctrl-0 = <&can0_pins_a>;
	pinctrl-1 = <&can0_pins_b>;
	status = "disabled";
};

&can1 {
	pinctrl-names = "default";
	pinctrl-0 = <&can1_pins_a>;
	pinctrl-1 = <&can1_pins_b>;
	status = "okay";
};

&soc {
	card0_boot_para@2 {
		/*
		 * Avoid dtc compiling warnings.
		 * @TODO: Developer should modify this to the actual value
		 */
		reg = <0x0 0x2 0x0 0x0>;
		device_type = "card0_boot_para";
		card_ctrl = <0x0>;
		card_high_speed = <0x1>;
		card_line = <0x4>;
		pinctrl-0 = <&sdc0_pins_a>;
	};

	card2_boot_para@3 {
		/*
		 * Avoid dtc compiling warnings.
		 * @TODO: Developer should modify this to the actual value
		 */
		reg = <0x0 0x3 0x0 0x0>;
		device_type = "card2_boot_para";
		card_ctrl = <0x2>;
		card_high_speed = <0x1>;
		card_line = <0x4>;
		pinctrl-0 = <&sdc2_pins_a>;
		/*pinctrl-0 = <&sdc0_pins_a>;*/
		/*sdc_ex_dly_used = <0x2>;*/
		sdc_io_1v8 = <0x1>;
		/*sdc_type = "tm4";*/
		sdc_tm4_hs200_max_freq = <150>;
		sdc_tm4_hs400_max_freq = <100>;
		sdc_ex_dly_used = <2>;
		/*sdc_tm4_win_th = <8>;*/
		/*sdc_dis_host_caps = <0x180>;*/
	};

	rfkill: rfkill@0 {
		compatible    = "allwinner,sunxi-rfkill";
		chip_en;
		power_en;
		pinctrl-0 = <&wlan_pins_a>;
		pinctrl-names = "default";
		status        = "disabled";

		wlan: wlan@0 {
			compatible    = "allwinner,sunxi-wlan";
			clock-names = "32k-fanout1";
			clocks = <&ccu CLK_FANOUT1_OUT>;
			wlan_busnum    = <0x1>;
			/* wlan_regon    = <&pio PG 12 GPIO_ACTIVE_HIGH>; */
			/* wlan_hostwake  = <&pio PG 10 GPIO_ACTIVE_HIGH>; */
			/*wlan_power    = "VCC-3V3";*/
			/*wlan_power_vol = <3300000>;*/
			/*interrupt-parent = <&pio>;
			interrupts = < PG 10 IRQ_TYPE_LEVEL_HIGH>;*/
			status     = "disabled";
			wakeup-source;
		};
		
		bt: bt@0 {
			compatible    = "allwinner,sunxi-bt";
			clock-names = "32k-fanout1";
			clocks = <&ccu CLK_FANOUT1_OUT>;
			/*bt_power_num = <0x01>;*/
			/*bt_power      = "axp803-dldo1";*/
			/*bt_io_regulator = "axp803-dldo1";*/
			/*bt_io_vol = <3300000>;*/
			/*bt_power_vol = <330000>;*/
			/* bt_rst_n      = <&pio PG 15 GPIO_ACTIVE_LOW>; */
			status        = "disabled";
		};
	};

	btlpm: btlpm@0 {
		compatible  = "allwinner,sunxi-btlpm";
		uart_index  = <0x1>;
		bt_wake     = <&pio PG 14 GPIO_ACTIVE_HIGH>;
		bt_hostwake = <&pio PG 13 GPIO_ACTIVE_HIGH>;
		status      = "disabled";
	};

	addr_mgt: addr_mgt@0 {
		compatible     = "allwinner,sunxi-addr_mgt";
		type_addr_wifi = <0x0>;
		type_addr_bt   = <0x0>;
		type_addr_eth  = <0x0>;
		status         = "okay";
	};
};

&sdc2 {
	non-removable;
	bus-width = <4>;
	mmc-ddr-1_8v;
	mmc-hs200-1_8v;
	no-sdio;
	no-sd;
	ctl-spec-caps = <0x308>;
	cap-mmc-highspeed;
	sunxi-power-save-mode;
	sunxi-dis-signal-vol-sw;
	mmc-bootpart-noacc;
	max-frequency = <150000000>;
	/*vmmc-supply = <&reg_dcdc1>;*/
	/*emmc io vol 3.3v*/
	/*vqmmc-supply = <&reg_aldo1>;*/
	/*emmc io vol 1.8v*/
	/*vqmmc-supply = <&reg_eldo1>;*/
	status = "disabled";
};

&sdc0 {
	bus-width = <4>;
	cd-gpios = <&pio PF 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* bingpi-m2 */
	/*non-removable;*/
	/*broken-cd;*/
	/*cd-inverted;*/
	/*data3-detect;*/
	/*card-pwr-gpios = <&pio PH 14 1 1 2 0xffffffff>;*/
	/*cd-used-24M;*/
	cap-sd-highspeed;
	/*sd-uhs-sdr50;*/
	/*sd-uhs-ddr50;*/
	/*sd-uhs-sdr104;*/
	no-sdio;
	no-mmc;
	sunxi-power-save-mode;
	/*sunxi-dis-signal-vol-sw;*/
	max-frequency = <150000000>;
	ctl-spec-caps = <0x8>;
	/*vmmc-supply = <&reg_dcdc1>;*/
	/*vqmmc33sw-supply = <&reg_dcdc1>;*/
	/*vdmmc33sw-supply = <&reg_dcdc1>;*/
	/*vqmmc18sw-supply = <&reg_eldo1>;*/
	/*vdmmc18sw-supply = <&reg_eldo1>;*/
	status = "disabled";
};

&sdc1 {
	bus-width = <4>;
	no-mmc;
	no-sd;
	cap-sd-highspeed;
	/*sd-uhs-sdr12*/
	/*sd-uhs-sdr25;*/
	/*sd-uhs-sdr50;*/
	/*sd-uhs-ddr50;*/
	/*sd-uhs-sdr104;*/
	/*sunxi-power-save-mode;*/
	/*sunxi-dis-signal-vol-sw;*/
	cap-sdio-irq;
	keep-power-in-suspend;
	ignore-pm-notify;
	max-frequency = <150000000>;
	ctl-spec-caps = <0x8>;
	status = "disabled";
};


/*
tvd configuration
used                   (create device, 0: do not create device, 1: create device)
agc_auto_enable        (0: agc manual mode,agc_manual_value is valid; 1: agc auto mode)
agc_manual_value       (agc manual value, default value is 64)
cagc_enable            (cagc        0: disable, 1: enable)
fliter_used            (3d fliter   0: disable, 1: enable)
support two PMU power  (tvd_power0, tvd_power1)
support two GPIO power (tvd_gpio0, tvd_gpio1)
NOTICE: If tvd need pmu power or gpio power,params need be configured under [tvd]
tvd_sw                 (the switch of all tvd driver.)
tvd_interface          (0: cvbs, 1: ypbpr,)
tvd_format             (0:TVD_PL_YUV420 , 1: MB_YUV420, 2: TVD_PL_YUV422)
tvd_system             (0:ntsc, 1:pal)
tvd_row                (total row number in multi channel mode 1-2)
tvd_column             (total column number in multi channel mode 1-2)
tvd_channelx_en        (0:disable, 1~4:position in multi channel mode,In single channel
                       mode,mean enable)
tvd_row*tvd_column is the total tvd channel number to be used in multichannel mode
+--------------------+--------------------+
|                    |                    |
|                    |                    |
|         1          |         2          |
|                    |                    |
|                    |                    |
+--------------------+--------------------+
|                    |                    |
|                    |                    |
|         3          |         4          |
|                    |                    |
|                    |                    |
+--------------------+--------------------+
*/

&tvd {
	tvd_sw          = <1>;
	tvd_interface   = <0>;
	tvd_format      = <0>;
	tvd_system      = <1>;
	tvd_row         = <1>;
	tvd_column      = <1>;
	tvd_channel0_en = <1>;
	tvd_channel1_en = <0>;
	tvd_channel2_en = <0>;
	tvd_channel3_en = <0>;
	/*tvd_gpio0 = <&pio PD 22 GPIO_ACTIVE_HIGH>;*/
	/*tvd_gpio1 = <&pio PD 23 GPIO_ACTIVE_HIGH>;*/
	/*tvd_gpio2 = <&pio PD 24 GPIO_ACTIVE_HIGH>;*/
	/*	dc1sw-supply = <&reg_dc1sw>;*/
	/*	eldo3-supply = <&reg_eldo3>;*/
	/*tvd_power0      = "dc1sw"*/
	/*tvd_power1      = "eldo3"*/
};

&tvd0 {
	used                    = <1>;
	agc_auto_enable         = <1>;
	agc_manual_value        = <64>;
	cagc_enable             = <1>;
	fliter_used             = <1>;
};

/* Audio Driver modules */
&sunxi_rpaf_dsp0 {
	status = "disabled";
};

/* if audiocodec is used, sdc0 and uart0 should be closed to enable PA. */
&codec {
	/* MIC and headphone gain setting */
	mic1gain 	= <0x1F>;
	mic2gain 	= <0x1F>;
	mic3gain 	= <0x1F>;
	/* ADC/DAC DRC/HPF func enabled */
        /* 0x1:DAP_HP_EN; 0x2:DAP_SPK_EN; 0x3:DAP_HPSPK_EN */
	adcdrc_cfg 	= <0x0>;
	adchpf_cfg 	= <0x1>;
	dacdrc_cfg 	= <0x0>;
	dachpf_cfg 	= <0x0>;
	/* Volume about */
	digital_vol 	= <0x00>;
	lineout_vol 	= <0x1a>;
	headphonegain	= <0x03>;
	/* Pa enabled about */
	pa_level 	= <0x01>;
	pa_pwr_level 	= <0x01>;
	pa_msleep_time 	= <0x78>;
	/* gpio-spk	= <&pio PF 2 GPIO_ACTIVE_HIGH>;*/
	/* gpio-spk-pwr	= <&pio PF 4 GPIO_ACTIVE_HIGH>; */
	/* CMA config about */
	playback_cma	= <128>;
	capture_cma	= <256>;
	/* regulator about */
	/* avcc-supply	= <&reg_aldo1>; */
	/* hpvcc-supply	= <&reg_eldo1>; */
	status = "okay";
};

&sndcodec {
	hp_detect_case	= <0x00>;
	jack_enable	= <0x01>;
	status = "okay";
};

&dummy_cpudai {
	status = "okay";
};

&dmic {
	pinctrl-names   = "default","sleep";
	pinctrl-0       = <&dmic_pins_a>;
	pinctrl-1       = <&dmic_pins_b>;
	status = "disabled";
};

&dmic_codec {
	status = "okay";
};

&sounddmic {
	status = "okay";
};

/*-----------------------------------------------------------------------------
 * pcm_lrck_period	16/32/64/128/256
 * slot_width_select	16bits/20bits/24bits/32bits
 * frametype		0 --> short frame = 1 clock width;
 *			1 --> long frame = 2 clock width;
 * tdm_config		0 --> pcm
 *			1 --> i2s
 * mclk_div		0 --> not output
 *			1/2/4/6/8/12/16/24/32/48/64/96/128/176/192
 *			(set mclk as external codec clk source, freq is pll_audio/mclk_div)
 * pinctrl_used		0 --> I2S/PCM use for internal
 *			1 --> I2S/PCM use for external audio
 * daudio_type:		0 --> external audio type
 *---------------------------------------------------------------------------*/
&daudio0 {
	mclk_div 	= <0x01>;
	frametype 	= <0x00>;
	tdm_config 	= <0x01>;
	sign_extend 	= <0x00>;
	msb_lsb_first 	= <0x00>;
	pcm_lrck_period = <0x80>;
	slot_width_select = <0x20>;
	pinctrl-names   = "default", "sleep";
	pinctrl-0       = <&daudio0_pins_a>;
	pinctrl-1       = <&daudio0_pins_b>;
	pinctrl_used	= <0x0>;
	status = "disabled";
};

/*-----------------------------------------------------------------------------
 * simple-audio-card,name	name of sound card, e.g.
 *				"snddaudio0" --> use for external audio
 * sound-dai			"snd-soc-dummy" --> use for I2S
 *				"ac108" --> use for external audio of ac108
 *---------------------------------------------------------------------------*/
&sounddaudio0 {
	/* simple-audio-card,format = "i2s"; */
	/* simple-audio-card,frame-master = <&daudio0_master>; */
	/* simple-audio-card,bitclock-master = <&daudio0_master>; */
	/* simple-audio-card,bitclock-inversion; */
	/* simple-audio-card,frame-inversion; */
	status = "disabled";
	daudio0_master: simple-audio-card,codec {
		/* sound-dai = <&ac108>; */
	};
};

&daudio1 {
	mclk_div 	= <0x01>;
	frametype 	= <0x00>;
	tdm_config 	= <0x01>;
	sign_extend 	= <0x00>;
	msb_lsb_first 	= <0x00>;
	pcm_lrck_period = <0x80>;
	slot_width_select = <0x20>;
	pinctrl-names   = "default", "sleep";
	pinctrl-0       = <&daudio1_pins_a>;
	pinctrl-1       = <&daudio1_pins_b>;
	pinctrl_used	= <0x0>;
	status = "disabled";
};

&sounddaudio1 {
	status = "disabled";
	daudio1_master: simple-audio-card,codec {
		/* sound-dai = <&ac108>; */
	};
};

&daudio2 {
	mclk_div 	= <0x01>;
	frametype 	= <0x00>;
	tdm_config 	= <0x01>;
	sign_extend 	= <0x00>;
	tx_data_mode 	= <0x00>;
	rx_data_mode 	= <0x00>;
	msb_lsb_first 	= <0x00>;
	pcm_lrck_period = <0x80>;
	slot_width_select = <0x20>;
	asrc_function_en  = <0x00>;
	pinctrl-names   = "default", "sleep";
	pinctrl-0       = <&daudio2_pins_a &daudio2_pins_b &daudio2_pins_c>;
	pinctrl-1       = <&daudio2_pins_d>;
	pinctrl_used	= <0x1>;
	daudio_type	= <0x0>;
	status = "disabled";
};

&sounddaudio2 {
	status = "disabled"; /* mangopi */
	daudio2_master: simple-audio-card,codec {
		/* sound-dai = <&ac108>; */
	};
};

&spdif {
	pinctrl-names   = "default","sleep";
	pinctrl-0       = <&spdif_pins_a>;
	pinctrl-1       = <&spdif_pins_b>;
	status = "okay";
};

&soundspdif {
	status = "okay";
};

/*
 *usb_port_type: usb mode. 0-device, 1-host, 2-otg.
 *usb_detect_type: usb hotplug detect mode. 0-none, 1-vbus/id detect, 2-id/dpdm detect.
 *usb_detect_mode: 0-thread scan, 1-id gpio interrupt.
 *usb_id_gpio: gpio for id detect.
 *usb_det_vbus_gpio: gpio for id detect. gpio or "axp_ctrl";
 *usb_wakeup_suspend：0-SUPER_STANDBY, 1-USB_STANDBY.
 */
&usbc0 {
	device_type = "usbc0";
	usb_port_type = <0x0>;
	usb_detect_type = <0x0>;
/*	usb_detect_mode = <0>;
	usb_id_gpio = <&pio PB 8 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	usb_det_vbus_gpio = <&pio PB 9 GPIO_ACTIVE_HIGH>; */
	usb_wakeup_suspend = <0>;
	usb_serial_unique = <0>;
	usb_serial_number = "20080411";
	rndis_wceis = <1>;
	status = "okay";
};

&ehci0 {
	drvvbus-supply = <&reg_usb1_vbus>;
};

&ohci0 {
	drvvbus-supply = <&reg_usb1_vbus>;
};

&usbc1 {
	device_type = "usbc1";
   	usb_port_type = <0x01>;
    	usb_detect_type = <0x1>;	
	usb_regulator_io = "nocare";
	usb_wakeup_suspend = <0>;
	status = "okay";
};

&ehci1 {
	status = "okay";
};

&ohci1 {
	status = "okay";
};

&twi0 {
	clock-frequency = <400000>;
	pinctrl-0 = <&twi0_pins_a>;
	pinctrl-1 = <&twi0_pins_b>;
	pinctrl-names = "default", "sleep";
	status = "disabled";

	eeprom@50 {
		compatible = "atmel,24c16";
		reg = <0x50>;
		status = "disabled";
	};
};

&twi1 {
	clock-frequency = <400000>;
	pinctrl-0 = <&twi1_pins_a>;
	pinctrl-1 = <&twi1_pins_b>;
	pinctrl-names = "default", "sleep";
	status = "disabled";
};

&twi2 {
	clock-frequency = <400000>;
	pinctrl-0 = <&twi2_pins_a>;
	pinctrl-1 = <&twi2_pins_b>;
	pinctrl-names = "default", "sleep";
	dmas = <&dma 45>, <&dma 45>;
	dma-names = "tx", "rx";
	status = "disabled";

	/* pcf8574-usage:
	 * only use gpio0~7, 0 means PP0.
	 * pin set:
	 * gpios = <&pcf8574 0 GPIO_ACTIVE_LOW>;
	 * interrupt set:
	 * interrupt-parent = <&pcf8574>;
	 * interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
	 */
	pcf8574: gpio@38 {
		compatible = "nxp,pcf8574";
		reg = <0x38>;
		gpio_base = <2020>;
		gpio-controller;
		#gpio-cells = <2>;
		interrupt-controller;
		#interrupt-cells = <2>;
		interrupt-parent = <&pio>;
		interrupts = <PB 2 IRQ_TYPE_EDGE_FALLING>;
		status = "disabled";
	};

	ctp@14 {
                compatible = "allwinner,goodix";
                device_type = "ctp";
                reg = <0x14>;
                status = "okay";
                ctp_name = "gt9xxnew_ts";
                ctp_twi_id = <0x2>;
                ctp_twi_addr = <0x14>;

                ctp_screen_max_x = <0x320>;
                ctp_screen_max_y = <0x1e0>;
                ctp_revert_x_flag = <0x0>;
                ctp_revert_y_flag = <0x0>;
                ctp_exchange_x_y_flag = <0x0>;


//type 1(mipi)
/*
		ctp_screen_max_x = <0x320>;
                ctp_screen_max_y = <0x500>;
                ctp_revert_x_flag = <0x1>;
                ctp_revert_y_flag = <0x0>;
                ctp_exchange_x_y_flag = <0x1>;
*/
//type 2(mipi)
/*
		ctp_screen_max_x = <0x320>;
                ctp_screen_max_y = <0x500>;
                ctp_revert_x_flag = <0x0>;
                ctp_revert_y_flag = <0x1>;
                ctp_exchange_x_y_flag = <0x1>;
*/
                ctp_int_port = <&pio PD 22 GPIO_ACTIVE_HIGH>;
                ctp_wakeup = <&pio PG 10 GPIO_ACTIVE_HIGH>;
                /*ctp-supply = <&reg_aldo2>;*/
                /*ctp_power_ldo = <&reg_aldo2>;*/
                /*ctp_power_ldo_vol = <3300>;*/
	};
};

&twi3 {
	clock-frequency = <400000>;
	pinctrl-0 = <&twi3_pins_a>;
	pinctrl-1 = <&twi3_pins_b>;
	pinctrl-names = "default", "sleep";
	status = "disabled";
};

&gmac0 {
	phy-mode = "rmii";
	use_ephy25m = <1>;
	pinctrl-0 = <&gmac_pins_a>;
	pinctrl-1 = <&gmac_pins_b>;
	pinctrl-names = "default", "sleep";
	phy-rst = <&pio PG 6 GPIO_ACTIVE_HIGH>;
	tx-delay = <7>; /*2~4*/
	rx-delay = <31>;
	status = "okay";
};

&spi0 {
	clock-frequency = <100000000>;
	pinctrl-0 = <&spi0_pins_a &spi0_pins_b>;
	pinctrl-1 = <&spi0_pins_c>;
	pinctrl-names = "default", "sleep";
	/*spi-supply = <&reg_dcdc1>;*/
	spi_slave_mode = <0>;
	spi0_cs_number = <1>;
    	spi0_cs_bitmap = <1>;
	status = "okay";

	spi-nand@0 {
		compatible = "spi-nand";
		spi-max-frequency=<100000000>;
		reg = <0x0>;
		spi-rx-bus-width=<0x01>;
		spi-tx-bus-width=<0x01>;
		status="okay";
	};

	spi-nor@0 {
		compatible = "jedec,spi-nor";
		spi-max-frequency=<30000000>;
		reg = <0x0>;
		spi-rx-bus-width=<0x01>;
		spi-tx-bus-width=<0x01>;
		status="disabled";
	};
};

&spi1 {
	clock-frequency = <100000000>;
	pinctrl-0 = <&spi1_pins_a &spi1_pins_b>;
	pinctrl-1 = <&spi1_pins_c>;
	pinctrl-names = "default", "sleep";
	spi_slave_mode = <0>;
	status = "okay";

	spi_board1@0 {
		device_type = "spi_board1";
		compatible = "rohm,dh2228fv";
		spi-max-frequency = <0x5f5e100>;
		reg = <0x0>;
		spi-rx-bus-width = <0x4>;
		spi-tx-bus-width = <0x4>;
		status = "disabled";
	};
		st7789v@0{
			status = "okay";
			compatible ="sitronix,st7789v";
			reg = <0>;
			spi-max-frequency = <6000000>;
			rotate = <0>;
			spi-cpol;
			spi-cpha;
			rgb;
			fps = <60>;
			buswidth = <8>;
			reset-gpios = <&pio PD 0 GPIO_ACTIVE_LOW>;
			dc-gpios = <&pio PD 1 GPIO_ACTIVE_LOW>;
			// led-gpios = <&pio PE 8 GPIO_ACTIVE_HIGH>;
			debug = <0>;
		};
};

&ledc {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&ledc_pins_a>;
	pinctrl-1 = <&ledc_pins_b>;
	led_count = <12>;
	output_mode = "GRB";
	reset_ns = <84>;
	t1h_ns = <800>;
	t1l_ns = <320>;
	t0h_ns = <300>;
	t0l_ns = <800>;
	wait_time0_ns = <84>;
	wait_time1_ns = <84>;
	wait_data_time_ns = <600000>;
	status	= "disabled";
};

&keyboard0 {
	key0 = <210 0x160>;
	wakeup-source;
	status = "disabled";
};



/*----------------------------------------------------------------------------------
disp init configuration

disp_mode             (0:screen0<screen0,fb0>)
screenx_output_type   (0:none; 1:lcd; 2:tv; 5:vdpo)
fbx format            (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
fbx pixel sequence    (0:ARGB 1:BGRA 2:ABGR 3:RGBA)
fb0_scaler_mode_enable(scaler mode enable, used FE)
fbx_width,fbx_height  (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
lcdx_backlight        (lcd init backlight,the range:[0,256],default:197
lcdx_yy               (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50)
lcd0_contrast         (LCD contrast, 0~100)
lcd0_saturation       (LCD saturation, 0~100)
lcd0_hue              (LCD hue, 0~100)
framebuffer software rotation setting:
disp_rotation_used:   (0:disable; 1:enable,you must set fbX_width to lcd_y,
set fbX_height to lcd_x)
degreeX:              (X:screen index; 0:0 degree; 1:90 degree; 3:270 degree)
degreeX_Y:            (X:screen index; Y:layer index 0~15; 0:0 degree; 1:90 degree; 3:270 degree)
devX_output_type : config output type in bootGUI framework in UBOOT-2018.
				   (0:none; 1:lcd; 2:tv;)
devX_output_mode : config output resolution(see include/video/sunxi_display2.h) of bootGUI framework in UBOOT-2018
devX_screen_id   : config display index of bootGUI framework in UBOOT-2018
devX_do_hpd      : whether do hpd detectation or not in UBOOT-2018
chn_cfg_mode     : Hardware DE channel allocation config. 0:single display with 6
				   channel, 1:dual display with 4 channel in main display and 2 channel in second
                   display, 2:dual display with 3 channel in main display and 3 channel in second
                   in display.
----------------------------------------------------------------------------------*/

&disp {
	disp_init_enable         = <1>;
	disp_mode                = <0>;

	screen0_output_type      = <1>;
	screen0_output_mode      = <4>;

	screen1_output_type      = <3>;
	screen1_output_mode      = <4>;
	
	screen1_output_format    = <0>;
	screen1_output_bits      = <0>;
	screen1_output_eotf      = <4>;
	screen1_output_cs        = <257>;
	screen1_output_range     = <2>;
	screen1_output_scan      = <0>;
	screen1_output_aspect_ratio = <8>;
	dev0_output_type         = <1>;
	dev0_output_mode         = <4>;
	dev0_screen_id           = <0>;
	dev0_do_hpd              = <0>;

	dev1_output_type         = <4>;
	dev1_output_mode         = <10>;
	dev1_screen_id           = <1>;
	dev1_do_hpd              = <1>;

	def_output_dev           = <0>;
	disp_rotation_used       = <1>;
	degree0			 = <0>;
	fb0_format               = <0>;
	fb0_buffer_num           = <1>;	
	//fb0_width                = <800>;
	//fb0_height               = <480>;
	fb1_format               = <0>;
	fb1_width                = <0>;
	fb1_height               = <0>;
	chn_cfg_mode             = <1>;

	disp_para_zone           = <1>;

	//dc1sw-supply = <&reg_dc1sw>;

	//eldo3-supply = <&reg_eldo3>;

	//dcdc1-supply = <&reg_dcdc1>;
};

/*----------------------------------------------------------------------------------
;lcd0 configuration

;lcd_if:               0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi
;lcd_hv_if             0:Parallel RGB; 8:Serial RGB; 10:Dummy RGB; 11: RGB Dummy;12:CCIR656
;lcd_hv_clk_phase      0:0 degree;1:90 degree;2:180 degree;3:270 degree
;lcd_hv_sync_polarity  0:vs low,hs low; 1:vs high,hslow; 2:vs low,hs high; 3:vs high,hs high
;lcd_hv_syuv_seq       0:YUYV; 1:YVYU; 2:UYVY; 3:VYUY
;lcd_cpu_if            0:18bit/1 cycle parallel(RGB666); 4:16bit/1cycle parallel (RGB565)
;                      6:18bit/3 cycle parallel(RGB666); 7:16bit/2cycle parallel (RGB565)
;lcd_cpu_te            0:frame auto trigger; 1:frame triggered by te rising edge; 2:frame triggered by te falling edge;
;lcd_dsi_if            0:video mode; 1: Command mode; 2:video burst mode
;lcd_dsi_te            0:frame auto trigger; 1:frame triggered by te rising edge; 2:frame triggered by te falling edge;
;lcd_x:                lcd horizontal resolution
;lcd_y:                lcd vertical resolution
;lcd_width:            width of lcd in mm
;lcd_height:           height of lcd in mm
;lcd_dclk_freq:        in MHZ unit
;lcd_pwm_freq:         in HZ unit
;lcd_pwm_pol:          lcd backlight PWM polarity
;lcd_pwm_max_limit     lcd backlight PWM max limit(<=255)
;lcd_hbp:              hsync back porch(pixel) + hsync plus width(pixel);
;lcd_ht:               hsync total cycle(pixel)
;lcd_vbp:              vsync back porch(line) + vysnc plus width(line)
;lcd_vt:               vysnc total cycle(line)
;lcd_hspw:             hsync plus width(pixel)
;lcd_vspw:             vysnc plus width(pixel)
;lcd_lvds_if:          0:single link;  1:dual link
;lcd_lvds_colordepth:  0:8bit; 1:6bit
;lcd_lvds_mode:        0:NS mode; 1:JEIDA mode
;lcd_frm:              0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_io_phase:         0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase;
;                      8~11bit:dclk phase; 12~15bit:de phase)
;lcd_gamma_en          lcd gamma correction enable
;lcd_bright_curve_en   lcd bright curve correction enable
;lcd_cmap_en           lcd color map function enable
;deu_mode              0:smoll lcd screen; 1:large lcd screen(larger than 10inch)
;lcdgamma4iep:         Smart Backlight parameter, lcd gamma vale * 10;
;                      decrease it while lcd is not bright enough; increase while lcd is too bright
;smart_color           90:normal lcd screen 65:retina lcd screen(9.7inch)
;Pin setting for special function ie.LVDS, RGB data or vsync
;   name(donot care) = port:PD12<pin function><pull up or pull down><drive ability><output level>
;Pin setting for gpio:
;   lcd_gpio_X     = port:PD12<pin function><pull up or pull down><drive ability><output level>
;Pin setting for backlight enable pin
;   lcd_bl_en     = port:PD12<pin function><pull up or pull down><drive ability><output level>
;fsync setting, pulse to csi
;lcd_fsync_en          (0:disable fsync,1:enable)
;lcd_fsync_act_time    (active time of fsync, unit:pixel)
;lcd_fsync_dis_time    (disactive time of fsync, unit:pixel)
;lcd_fsync_pol         (0:positive;1:negative)
;gpio config: <&pio for cpu or &r_pio for cpus, port, port num, pio function,
pull up or pull down(default 0), driver level(default 1), data>
;For dual link lvds: use lvds2link_pins_a  and lvds2link_pins_b instead
;For rgb24: use rgb24_pins_a  and rgb24_pins_b instead
;For lvds1: use lvds1_pins_a  and lvds1_pins_b instead
;For lvds0: use lvds0_pins_a  and lvds0_pins_b instead
;----------------------------------------------------------------------------------*/

// 480x272 RGB LCD
/*
&lcd0 {
	lcd_used            = <1>;

	lcd_driver_name     = "default_lcd";
	lcd_backlight       = <50>;
	lcd_if              = <0>;

	lcd_x               = <480>;
	lcd_y               = <272>;
	lcd_width           = <95>;
	lcd_height          = <54>;
	lcd_dclk_freq       = <9>;

	lcd_pwm_used        = <0>;
	lcd_pwm_ch          = <7>;
	lcd_pwm_freq        = <50000>;
	lcd_pwm_pol         = <1>;

	lcd_hbp             = <43>;
	lcd_ht              = <525>;
	lcd_hspw            = <41>;
	lcd_vbp             = <12>;
	lcd_vt              = <286>;
	lcd_vspw            = <10>;

	lcd_lvds_if         = <0>;
	lcd_lvds_colordepth = <1>;
	lcd_lvds_mode       = <0>;
	lcd_frm             = <1>;
	lcd_io_phase        = <0x0000>;
	lcd_gamma_en        = <0>;
	lcd_bright_curve_en = <0>;
	lcd_cmap_en         = <0>;

	deu_mode            = <0>;
	lcdgamma4iep        = <22>;
	smart_color         = <90>;

	pinctrl-0 = <&rgb18_pins_a>;
	pinctrl-1 = <&rgb18_pins_b>;
};
*/
// 800x480 RGB LCD
&lcd0 {
	lcd_used            = <1>;

	lcd_driver_name     = "default_lcd";
	lcd_backlight       = <50>;
	lcd_if              = <0>;

	lcd_x               = <800>;
	lcd_y               = <480>;
	lcd_width           = <95>;
	lcd_height          = <54>;
	lcd_dclk_freq       = <33>;

	lcd_pwm_used        = <0>;
	lcd_pwm_ch          = <7>;
	lcd_pwm_freq        = <50000>;
	lcd_pwm_pol         = <1>;

	lcd_hbp             = <41>;
	lcd_ht              = <928>;
	lcd_hspw            = <2>;
	lcd_vbp             = <14>;
	lcd_vt              = <525>;
	lcd_vspw            = <2>;

	lcd_lvds_if         = <0>;
	lcd_lvds_colordepth = <1>;
	lcd_lvds_mode       = <0>;
	lcd_frm             = <1>;
	lcd_io_phase        = <0x0000>;
	lcd_gamma_en        = <0>;
	lcd_bright_curve_en = <0>;
	lcd_cmap_en         = <0>;

	deu_mode            = <0>;
	lcdgamma4iep        = <22>;
	smart_color         = <90>;

	pinctrl-0 = <&rgb18_pins_a>;
	pinctrl-1 = <&rgb18_pins_b>;
};

// 1024x600 RGB LCD
/*
&lcd0 {
	lcd_used            = <1>;

	lcd_driver_name     = "default_lcd";
	lcd_backlight       = <50>;
	lcd_if              = <0>;

	lcd_x               = <1024>;
	lcd_y               = <600>;
	lcd_width           = <95>;
	lcd_height          = <54>;
	lcd_dclk_freq       = <51>;

	lcd_pwm_used        = <0>;
	lcd_pwm_ch          = <7>;
	lcd_pwm_freq        = <50000>;
	lcd_pwm_pol         = <1>;

	lcd_hbp             = <160>;
	lcd_ht              = <1344>;
	lcd_hspw            = <20>;
	lcd_vbp             = <23>;
	lcd_vt              = <635>;
	lcd_vspw            = <3>;

	lcd_lvds_if         = <0>;
	lcd_lvds_colordepth = <1>;
	lcd_lvds_mode       = <0>;
	lcd_frm             = <1>;
	lcd_io_phase        = <0x0000>;
	lcd_gamma_en        = <0>;
	lcd_bright_curve_en = <0>;
	lcd_cmap_en         = <0>;

	deu_mode            = <0>;
	lcdgamma4iep        = <22>;
	smart_color         = <90>;

	pinctrl-0 = <&rgb18_pins_a>;
	pinctrl-1 = <&rgb18_pins_b>;
};
*/

// 1280x800 MIPI LCD
/*
&lcd0 {
	lcd_used            = <1>;

	lcd_driver_name     = "he0801a068";
	lcd_backlight       = <50>;
	lcd_if              = <4>;

	lcd_x               = <800>;
	lcd_y               = <1280>;
	lcd_width           = <52>;
	lcd_height          = <52>;
	lcd_dclk_freq       = <68>;

	lcd_pwm_used        = <1>;
	lcd_pwm_ch          = <7>;
	lcd_pwm_freq        = <50000>;
	lcd_pwm_pol         = <1>;
	lcd_pwm_max_limit   = <255>;

	lcd_hbp             = <40>;
	lcd_ht              = <860>;
	lcd_hspw            = <20>;
	lcd_vbp             = <12>;
	lcd_vt              = <1322>;
	lcd_vspw            = <4>;

	lcd_dsi_lane        = <4>;
	lcd_dsi_if          = <0>;
	lcd_dsi_format      = <0>;
	lcd_dsi_te          = <0>;
	lcd_frm             = <0>;
	lcd_gamma_en        = <0>;
	lcd_cmap_en         = <0>;

	pinctrl-0 = <&dsi4lane_pins_a>;
	pinctrl-1 = <&dsi4lane_pins_b>;
	//lcd_gpio_0 = <&pio PD 20 1 0 3 1>;
};
*/

&pwm0 {
	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&pwm0_pin_a>;
	pinctrl-1 = <&pwm0_pin_b>;
	status = "disabled";
};

&pwm2 {
	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&pwm2_pin_a>;
	pinctrl-1 = <&pwm2_pin_b>;
	status = "disabled";
};


&pwm7 {
	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&pwm7_pin_a>;
	pinctrl-1 = <&pwm7_pin_b>;
	status = "disabled";
};

&rtp {
	allwinner,tp-sensitive-adjust = <0xf>;
	allwinner,filter-type = <0x1>;
	allwinner,ts-attached;
	status = "okay";
};

&tpadc {
	key_cnt = <5>;
	key1 = <420 115>;
	key2 = <870 114>;
	key3 = <1290 119>;
	key4 = <1630 373>;
	key5 = <1950 28>;
	status = "disabled";
};

&gpadc {
	channel_num = <1>;
	channel_select = <0x01>;
	channel_data_select = <0>;
	channel_compare_select = <0x01>;
	channel_cld_select = <0x01>;
	channel_chd_select = <0>;
	channel0_compare_lowdata = <1600000>;
	channel0_compare_higdata = <1200000>;
	channel1_compare_lowdata = <460000>;
	channel1_compare_higdata = <1200000>;
	key_cnt = <5>;
	key0_vol = <210>;
	key0_val = <0x19c>;
	key1_vol = <410>;
	key1_val = <0x197>;
	key2_vol = <590>;
	key2_val = <158>;
	key3_vol = <750>;
	key3_val = <28>;
	key4_vol = <880>;
	key4_val = <28>;
	status = "disabled";
	wakeup-source;
};

&s_cir0 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&s_cir0_pins_a>;
	pinctrl-1 = <&s_cir0_pins_b>;
	ir_protocol_used		= <0>;
	ir_addr_code0			= <0x0>;
	status = "disabled";
};

&ir1 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&ir1_pins_a>;
	pinctrl-1 = <&ir1_pins_b>;
	status = "disabled";
};