SmartPDCode/truring_ctrl_upgrade/PDU-DC_ADA/hardware/uart/uart.c

#include "uart.h"
#include "board_cfg.h"
#include "common.h"
#include "gd32e23x.h"
#include "Hlw8110.h"
#include "stdbool.h"
#include "systick.h"


#define UART1_BUF_SIZE 64 
#define IM1253E_bd     4800


unsigned char	u8_RxBuf[UART1_BUF_SIZE];
unsigned char	u8_TX_Length;

unsigned char	u8_RX_Index;

unsigned char	B_Rx_Finish;
unsigned char	RX_Length;


Rx_Data data={0};


void uart1_config(uint32_t bound)
{
	nvic_irq_enable(USART1_IRQn, 2);
	rcu_periph_clock_enable(RCU_GPIOA);
	gpio_af_set(GPIOA, GPIO_AF_1, GPIO_PIN_2); 
	gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_2);
	gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, GPIO_OSPEED_10MHZ, GPIO_PIN_2);
	
	gpio_af_set(GPIOA, GPIO_AF_1, GPIO_PIN_3);
	gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_3);
  gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, GPIO_OSPEED_10MHZ, GPIO_PIN_3);
	
	rcu_periph_clock_enable(RCU_USART1); 
	usart_deinit(USART1);
	usart_baudrate_set(USART1, bound);
	usart_stop_bit_set(USART1,USART_STB_1BIT);

	usart_word_length_set(USART1,USART_WL_8BIT);
	usart_parity_config(USART1,USART_PM_NONE); 
	usart_receive_config(USART1, USART_RECEIVE_ENABLE);
	usart_transmit_config(USART1, USART_TRANSMIT_ENABLE);
	usart_enable(USART1);
	usart_interrupt_enable(USART1, USART_INT_RBNE);

}




void USART1_IRQHandler(void)
{
	if(usart_flag_get(USART1, USART_FLAG_ORERR) == SET)
  {                                                         
    usart_flag_clear(USART1, USART_FLAG_ORERR);       
  } 
	if(usart_interrupt_flag_get(USART1, USART_INT_FLAG_TBE)!= RESET) 
  {     
    usart_interrupt_flag_clear(USART1, USART_INT_FLAG_TBE);       
  }
	if(usart_interrupt_flag_get(USART1, USART_INT_FLAG_RBNE) != RESET) 
	{
		usart_interrupt_flag_clear(USART1, USART_INT_FLAG_RBNE);
		if (u8_RX_Index < RX_Length )
		{
#if SUPPORT_STM32_ADC
		extern Rx_Data data;
		data.data[u8_RX_Index] = usart_data_receive(USART1);			
#else
			u8_RxBuf[u8_RX_Index] = usart_data_receive(USART1); 
#endif
			u8_RX_Index++;
			if(u8_RX_Index >= RX_Length)
			{
				B_Rx_Finish = TRUE;	
				u8_RX_Index = 0;
			}
		}
	}
}


#if SUPPORT_STM32_ADC



uint32_t read_stm_voltage(uint8_t channel)
{
	uint16_t r_volatge = 0xA5A5;
	uint32_t value;
	RX_Length = 4;
	che442_change_ch(channel);
	DelayNms(5);
	//memset(&data.value,0,4);
	Start_Send_UartData((uint8_t*)&r_volatge,sizeof(r_volatge));
	int count = 0;
	while(B_Rx_Finish != TRUE)
	{
		DelayNms(1);
		if(count >= 100)
		{
			u8_RX_Index = 0;
			B_Rx_Finish = FALSE;
			break;
		}
		count++;
	}
	if(B_Rx_Finish == FALSE)
	{
		count =0;
		Start_Send_UartData((uint8_t*)&r_volatge,sizeof(r_volatge));
		while(B_Rx_Finish != TRUE)
		{
			DelayNms(1);
			if(count >= 100)
			{
				u8_RX_Index = 0;
				B_Rx_Finish =FALSE;
				break;
			}
			count ++;
		}
	}
	if(B_Rx_Finish)
	{
		value = data.value;
		B_Rx_Finish = false;
	}else
		value = 0;
	return value;
}

#endif


void Start_Send_UartData(uint8_t *pt,uint8_t len)
{
	uint8_t i;
	for(i = 0;i < len;i++)
	{
		usart_data_transmit(USART1, *(pt+i));  	//发送字符函数
		while(usart_flag_get(USART1, USART_FLAG_TC) == RESET);//等待发送结束
	}
}

#if SUPPORT_STM32_ADC



#define     CH442E_GPIO           GPIOA
#define     CH442E_RCU            RCU_GPIOA
#define     CH442E_IN_GPIO				GPIO_PIN_15
#define 		CH442E_EN_GPIO				GPIO_PIN_12





#define      CHOISE_STM32_1			gpio_bit_set(CH442E_GPIO, CH442E_IN_GPIO)

#define      CHOISE_STM32_2			gpio_bit_reset(CH442E_GPIO, CH442E_IN_GPIO) 


void che442e_Init(void)
{
	rcu_periph_clock_enable(CH442E_RCU); 
	gpio_mode_set(CH442E_GPIO, GPIO_MODE_OUTPUT, GPIO_PUPD_PULLDOWN, CH442E_IN_GPIO | CH442E_EN_GPIO);
	gpio_bit_set(CH442E_GPIO, CH442E_IN_GPIO);
	gpio_bit_reset(CH442E_GPIO, CH442E_EN_GPIO);
}





void che442_change_ch(uint8_t channel)
{
	switch(channel)
	{
		case STM32_ADC_V_1:
			CHOISE_STM32_1;
		break;
		case STM32_ADC_V_2:
			CHOISE_STM32_2;
		break;
		default:
			break;
	}
}
#endif