SmartPDCode/485/src/modbus_handle.c

#include "modbus_handle.h"
#include <sys/ioctl.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <asm/ioctls.h>
#include <errno.h>
#include <termios.h> 
#include <string.h>
struct rs485_ctrl {
  unsigned short rts_on_send;
  unsigned short rts_after_sent;
  unsigned int  delay_rts_before_send;
  unsigned short enabled;
};

/// @brief 初始化modbus
/// @param manger 
/// @param port_name 
/// @param type 
/// @param saddr 
/// @param name 
/// @return 
int g_modbus_init(void* manger,
                const char* port_name,
                unsigned int baud,
                unsigned char type,
                unsigned char saddr,
                const char* name)
{
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger;
    modbus_manger->port_name = port_name;
    modbus_manger->baud = baud;
    modbus_manger->type = type;
    modbus_manger->saddr = saddr;
    strcpy(modbus_manger->name,name);
    //初始化
    modbus_manger->mb = modbus_new_rtu(modbus_manger->port_name, modbus_manger->baud,'N', 8, 1);
    printf(modbus_strerror(errno));
    if(modbus_manger->mb == NULL)
        return -1;
    manger = modbus_manger;
    //设置从机地址
     if(modbus_manger->saddr > 0){
        modbus_set_slave(modbus_manger->mb, modbus_manger->saddr);
        modbus_manger->mmp =  modbus_mapping_new_start_address(0,0,0,0,0x1770,22,0x177B,10);
     }
         
    //链接
    int ret = modbus_connect(modbus_manger->mb);
    //if (ret!=0)
    //{
        
     //   return -5;
        /* code */
   // }

    //int fd;
    //struct rs485_ctrl ctrl485;
    //fd = modbus_get_socket(modbus_manger->mb);
    //ctrl485.rts_on_send = 0;           // It means that DE is at 3.3 volt on send
    //ctrl485.rts_after_sent = 1;        // It means that DE is at 0 volt on send
    //ctrl485.delay_rts_before_send = 0; // DE will be active at same time of data
    //ctrl485.enabled = 1;
    //ret = ioctl(fd, TIOCSRS485, &ctrl485);  
    //if (ret) {
    //    printf("ERROR PORT 1! TIOCSERSETRS485 failed %i\n", ret);
    //    return -2;
    //}

    //设置为485模式
    //int nModeType = modbus_rtu_get_rts(modbus_manger->mb);
    //if (nModeType != MODBUS_RTU_RTS_NONE)
    //{

    //}
    //ret = modbus_set_debug(modbus_manger->mb,TRUE);
    ret = modbus_rtu_set_serial_mode(modbus_manger->mb, MODBUS_RTU_RS485);
    if (ret != 0)
    {
        printf(modbus_strerror(errno));

       //return -2;
      /* code */
    }
    //启用RTS模式并同时设置极性
    ret = modbus_rtu_set_rts(modbus_manger->mb, MODBUS_RTU_RTS_NONE);
    if (ret != 0)
    {

       return -3;
      /* code */
    }

    ret =modbus_set_error_recovery(modbus_manger->mb,MODBUS_ERROR_RECOVERY_PROTOCOL | MODBUS_ERROR_RECOVERY_LINK);
    //设置超时时间为2S
    struct timeval response_timeout;
    response_timeout.tv_sec = 4;
    response_timeout.tv_usec = 0;
    // modbus_set_response_timeout(modbus_manger->mb,2,1500000);
    // modbus_set_byte_timeout(modbus_manger->mb,0,1000000);
    //modbus_set_debug(modbus_manger->mb,1);

    //modbus_set_response_timeout(modbus_manger->mb,3,100000);  
    //初始化锁
    ret = pthread_mutex_init(&modbus_manger->mutex,NULL);
    if (ret!=0)
    {
    
        return -4;
      /* code */
    }
    return 0;
}




int d_g_modbus_init(void* manger,
                const char* port_name,
                unsigned int baud,
                unsigned char type,
                unsigned char saddr,
                const char* name)
{
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger;
    modbus_manger->port_name = port_name;
    modbus_manger->baud = baud;
    modbus_manger->type = type;
    modbus_manger->saddr = saddr;
    strcpy(modbus_manger->name,name);
    //初始化
    modbus_manger->mb = modbus_new_rtu(modbus_manger->port_name, modbus_manger->baud,'N', 8, 1);
    printf(modbus_strerror(errno));
    if(modbus_manger->mb == NULL)
        return -1;
    manger = modbus_manger;
    //设置从机地址,主机默认为0
     if(modbus_manger->saddr > 0 ){
        modbus_set_slave(modbus_manger->mb, modbus_manger->saddr);
        modbus_manger->mmp =  modbus_mapping_new_start_address(0,0,0,0,0x1770,22,0x177B,10);
     }
         
    //链接
    int ret = modbus_connect(modbus_manger->mb);
    //if (ret!=0)
    //{
        
     //   return -5;
        /* code */
   // }

    //int fd;
    //struct rs485_ctrl ctrl485;
    //fd = modbus_get_socket(modbus_manger->mb);
    //ctrl485.rts_on_send = 0;           // It means that DE is at 3.3 volt on send
    //ctrl485.rts_after_sent = 1;        // It means that DE is at 0 volt on send
    //ctrl485.delay_rts_before_send = 0; // DE will be active at same time of data
    //ctrl485.enabled = 1;
    //ret = ioctl(fd, TIOCSRS485, &ctrl485);  
    //if (ret) {
    //    printf("ERROR PORT 1! TIOCSERSETRS485 failed %i\n", ret);
    //    return -2;
    //}

    //设置为485模式
    //int nModeType = modbus_rtu_get_rts(modbus_manger->mb);
    //if (nModeType != MODBUS_RTU_RTS_NONE)
    //{

    //}
    ret = modbus_set_debug(modbus_manger->mb,TRUE);
    ret = modbus_rtu_set_serial_mode(modbus_manger->mb, MODBUS_RTU_RS485);
    if (ret != 0)
    {
        printf(modbus_strerror(errno));

       //return -2;
      /* code */
    }
    //启用RTS模式并同时设置极性
    ret = modbus_rtu_set_rts(modbus_manger->mb, MODBUS_RTU_RTS_NONE);
    if (ret != 0)
    {

       return -3;
      /* code */
    }
    //设置超时时间为2S
    struct timeval response_timeout;
    response_timeout.tv_sec = 4;
    response_timeout.tv_usec = 0;
    modbus_set_response_timeout(modbus_manger->mb,2,1500000);
    modbus_set_byte_timeout(modbus_manger->mb,0,1000000);
    //modbus_set_debug(modbus_manger->mb,1);

    //modbus_set_response_timeout(modbus_manger->mb,3,100000);  
    //初始化锁
    ret = pthread_mutex_init(&modbus_manger->mutex,NULL);
    if (ret!=0)
    {
    
        return -4;
      /* code */
    }
    return 0;
}

/// @brief 写单个寄存器值
/// @param manger 
/// @param reg 
/// @param data 
/// @return 
int g_modbus_write_reg(void* manger,int saddr,unsigned short reg,unsigned short data)
{
    int ret = 0 ;
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger; 
    pthread_mutex_lock(&modbus_manger->mutex);
    usleep(10000);
    modbus_set_slave(modbus_manger->mb, saddr);
    ret=modbus_write_register(modbus_manger->mb, reg, data);//06
    pthread_mutex_unlock(&modbus_manger->mutex);
    return ret;
}

/// @brief 写多个寄存器
/// @param manger 
/// @param reg 
/// @param size 
/// @param data 
/// @return 
int g_modbus_write_x_reg(void* manger,int saddr,unsigned short reg,unsigned int size,unsigned short *data)
{
    int ret = 0 ;
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger;
    pthread_mutex_lock(&modbus_manger->mutex);
    usleep(10000);
    modbus_set_slave(modbus_manger->mb, saddr);
    ret = modbus_write_registers(modbus_manger->mb, reg, size,data);//06
    pthread_mutex_unlock(&modbus_manger->mutex);
    return ret ;
}

/// @brief 读取单个寄存器值
/// @param manger 
/// @param reg 
/// @param data 
/// @return 
int g_modbus_read_reg(void* manger,int saddr,unsigned short reg,unsigned short *data)
{
    int ret = 0 ;
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger;    
    pthread_mutex_lock(&modbus_manger->mutex); 
    usleep(30000);  
    modbus_set_slave(modbus_manger->mb, saddr); 
    ret = modbus_read_registers(modbus_manger->mb, reg, 1, data);//0x03
    pthread_mutex_unlock(&modbus_manger->mutex);
    return ret;
}

/// @brief 读取多个寄存器值
/// @param manger 
/// @param reg 
/// @param size 
/// @param data 
/// @return 
int g_modbus_read_x_reg(void* manger,int saddr,unsigned short reg,unsigned int size,unsigned short *data)
{
    int ret = 0 ;
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger; 
    pthread_mutex_lock(&modbus_manger->mutex);
    usleep(30000); 
    modbus_set_slave(modbus_manger->mb, saddr);   
    ret = modbus_read_registers(modbus_manger->mb, reg, size, data);//0x03 
    pthread_mutex_unlock(&modbus_manger->mutex);
    return ret ;
}

/// @brief 读取多个寄存器值-延时版
/// @param manger 
/// @param reg 
/// @param size 
/// @param data 
/// @return 
int g_modbus_read_x_reg_delay(void* manger,int saddr,unsigned short reg,unsigned int size,unsigned short *data)
{
    int ret = 0 ;
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger; 
    pthread_mutex_lock(&modbus_manger->mutex); 
    usleep(30000); 
    modbus_set_slave(modbus_manger->mb, saddr);   
    ret = modbus_read_registers(modbus_manger->mb, reg, size, data);//0x03 
    pthread_mutex_unlock(&modbus_manger->mutex);
    return ret ;
}


/// @brief 释放modbus接口
/// @param manger 
void g_modbus_deinit(void* manger)
{
    Modbus_Manger *modbus_manger = (Modbus_Manger *)manger;
    modbus_close(modbus_manger->mb);
    modbus_free(modbus_manger->mb);
    pthread_mutex_destroy(&modbus_manger->mutex);
}