SmartPDCode/output/t113s/pack_dir/etc/init.d/rc.modules

#!/bin/sh
echo "------run rc.modules file-----"

#export boot_partition=$(fw_printenv -n boot_partition 2>/dev/null)
# if [ x${boot_partition} == xboot ];then 
#	/sbin/insmod /lib/modules/5.4.61/usb-storage.ko
#	/sbin/insmod /lib/modules/5.4.61/sunxi_gpadc.ko
	/sbin/insmod /lib/modules/5.4.61/gt9xxnew_ts.ko
	echo 0x07090160 0x083F10F7 > /sys/class/sunxi_dump/write
#	/sbin/insmod /lib/modules/5.4.61/8723ds.ko
#	/sbin/insmod /lib/modules/5.4.61/8189fs.ko
#	/sbin/insmod /lib/modules/5.4.61/r8188eu.ko
#	/sbin/insmod /lib/modules/5.4.61/8821cu.ko
#	sleep 1
#	wpa_supplicant -D wext -c /etc/wpa_supplicant.conf -i wlan0 &
#	udhcpc -i wlan0
#	wpa_supplicant  -Dnl80211 -iwlan0 -c /etc/wifi/wpa_supplicant.conf -B

amixer -D hw:audiocodec cset name='Headphone Switch' 1 && \
amixer -D hw:audiocodec cset name='Headphone volume' 25


#ifconfig eth0 192.168.1.132 up




# 读取interfaces文件  
INTERFACES_FILE="/etc/network/interfaces"  
  
# 检查文件是否存在  
if [ ! -f "$INTERFACES_FILE" ]; then  
    echo "Error: $INTERFACES_FILE not found."  
    `ifconfig  eth0 192.168.1.132 up`
fi
# else

#     ifconfig eth0 up

#     sleep 2

#     /sbin/udhcpc -n
#     if [ $? -eq 1 ]; then
#       sleep 1
#       interface="eth0"  
#       ip_address=""  
#       netmask=""
#       gateway=""
#       while IFS= read -r line; do  
#         # 检查行是否以 iface 开始，并包含指定的接口名  
#         if [[ "$line" == "iface $interface inet static" ]]; then  
#             # 读取下一行，它应该是 address  
#             while read -r next_line; do  
#               # 检查下一行是否以 address 开始  
#               if echo "$next_line" | grep -q "address" ; then  
#                   # 提取IP地址（从"address "之后开始）  
#                   ip_address=`echo ${next_line} | awk -F ' ' '{print $2}'`
#                   #echo $ip_address
#                   #break  # 找到IP后退出循环  
#               elif echo "$next_line" | grep -q "netmask" ;then
#                 netmask=`echo ${next_line} | awk -F ' ' '{print $2}'`
#               elif echo "$next_line" | grep -q "gateway" ;then
#                 gateway=`echo ${next_line} | awk -F ' ' '{print $2}'`
#               else
#                 break
#                 #echo "asdas"
#               fi 
            
#             done
            
#         fi  
#       done < $INTERFACES_FILE 


#       echo "$interface" "$ip_address"  "$gateway" "$netmask"
#       if [[ "$ip_address" == ""  ]]; then
#         `ifconfig  eth0 192.168.1.132 up`
#       else
#         `ifconfig "$interface" "$ip_address" netmask "$netmask" up`
#         `route del default`
#         `route add default gw "$gateway"`
#       fi
#     else
#       echo "hello udhcp!!!"
#     fi

# fi  
  
interface="eth0"  
ip_address=""  
netmask=""
gateway=""
auto_flag=""
ip_flag=""

ipv6_addrss=""
ipv6_netmask=""
ipv6_gateway=""
ipv6_autoflag=""
hw_addr=""

if [[ -f /sys/class/addr_mgt/addr_eth ]];then
        hw_addr=`cat /sys/class/addr_mgt/addr_eth`
fi

echo "hw  $hw_addr"


ifconfig  $interface hw ether $hw_addr
ifconfig $interface up


while IFS= read -r line; do 
	if [[ "$line" == "iface $interface inet static" ]]; then
		ip_flag="1"
		auto_flag="1"
	elif [[ "$line" == "iface $interface inet dhcp" ]];then
		ip_flag="2"
		auto_flag="2"
  elif [[ "$line" == "iface $interface inet6 static" ]];then
    ip_flag="3"
		ipv6_autoflag="3"
  elif [[ "$line" == "iface $interface inet6 dhcp" ]];then
    ip_flag="4"
    ipv6_autoflag="4"   
	fi
	if [[ "$ip_flag" == "1" ]]; then
		if echo "$line" | grep -q "address" ; then  
      # 提取IP地址（从"address "之后开始）  
			ip_address=`echo ${line} | awk -F ' ' '{print $2}'`
                  #echo $ip_address
                  #break  # 找到IP后退出循环  
    elif echo "$line" | grep -q "netmask" ;then
			netmask=`echo ${line} | awk -F ' ' '{print $2}'`
    elif echo "$line" | grep -q "gateway" ;then
			gateway=`echo ${line} | awk -F ' ' '{print $2}'`
    fi 
		if [[ "$ip_address" != "" && "$netmask" != "" && "$gateway" != "" ]]; then
			ip_flag=""
		fi
  elif [[ "$ip_flag" == "3" ]]; then
		if echo "$line" | grep -q "address" ; then  
      # 提取IP地址（从"address "之后开始）  
			ipv6_addrss=`echo ${line} | awk -F ' ' '{print $2}'`
                  #echo $ip_address
                  #break  # 找到IP后退出循环  
    elif echo "$line" | grep -q "netmask" ;then
			ipv6_netmask=`echo ${line} | awk -F ' ' '{print $2}'`
    elif echo "$line" | grep -q "gateway" ;then
			ipv6_gateway=`echo ${line} | awk -F ' ' '{print $2}'`
    fi 
		if [[ "$ipv6_addrss" != "" && "$ipv6_netmask" != "" && "$ipv6_gateway" != "" ]]; then
			ip_flag=""
		fi   
	fi
done < $INTERFACES_FILE 

echo $ip_address $netmask $gateway  $auto_flag $ip_flag
echo $ipv6_addrss $ipv6_netmask $ipv6_gateway  $ipv6_autoflag $ip_flag

if [[ "$auto_flag" == "1" && "$ip_address" != "" && "$netmask" != "" && "$gateway" != "" ]];then
#	`ifconfig  $interface hw ether $hw_addr`
  `ifconfig "$interface" "$ip_address" netmask "$netmask" up`
  `route del default`
  `route add default gw "$gateway"`

	echo "Static"
elif [[ "$auto_flag" == "2"  ]];then
	echo "get is DHCPC"
	/sbin/udhcpc  &
	sleep 4
#  `ifconfig  $interface hw ether $hw_addr`
else
	echo "Other FAILED" 
  `ifconfig  eth0 192.168.1.132 up`
  `ifconfig  $interface hw ether $hw_addr`
	echo "" > $INTERFACES_FILE
	echo "# interface file auto-generated by buildroot" >> $INTERFACES_FILE
	echo "auto lo" >> $INTERFACES_FILE
	echo "iface lo inet loopback" >> $INTERFACES_FILE
	echo "auto eth0" >> $INTERFACES_FILE
	echo "iface eth0 inet static" >> $INTERFACES_FILE
	echo "address 192.168.1.132" >> $INTERFACES_FILE
	echo "netmask 255.255.255.0" >> $INTERFACES_FILE
	echo "gateway 192.168.1.0" >> $INTERFACES_FILE
	echo "" >> $INTERFACES_FILE
	echo "" >> $INTERFACES_FILE
	echo "" >> $INTERFACES_FILE
fi


if [[ "$ipv6_autoflag" == "3" && "$ipv6_addrss" != "" && "$ipv6_netmask" != "" && "$ipv6_gateway" != "" ]];then
	`ifconfig "$interface" "$ipv6_addrss/$ipv6_netmask" up`
  #`route -A inet6 add default gw $ipv6_gateway dev $interface`
	 echo "IPV6 static"
elif [[ "$auto_flag" == "4"  ]];then
	echo "get is DHCPCP"
else
	echo "Other FAILED" 
  #`ifconfig  eth0 192.168.1.132 up`
fi



./opt/led_flash &

ssh-keygen -A

/etc/init.d/sshd start

export QT_BOOT=/usr/lib/arm-qt
export QTDIR=/usr/lib/arm-qt
export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/usr/lib/arm-qt/lib
export LD_LIBRARY_PATH=$QTDIR/lib:$QTDIR/plugins/platforms:$LD_LIBRARY_PATH
export QT_PLUGIN_PATH=$QTDIR/plugins
export QT_QPA_GENERIC_PLUGINS=tslib:$TSLIB_TSDEVICE
export QT_QPA_FONTDIR=$QTDIR/lib/fonts
export QT_QPA_PLATFORM_PLUGIN_PATH=$QTDIR/plugins
export QT_QPA_PLATFORM=linuxfb:fb=/dev/fb1


RUNDIR=/mnt/UDISK
APPDIR=$RUNDIR/app
WEBDIR=$RUNDIR/web
SNMPDIR=$APPDIR/snmp

# source /etc/qtenv.sh
export MIBDIRS=$SNMPDIR/mibs
export LD_LIBRARY_PATH=$APPDIR/lib:${LD_LIBRARY_PATH}


start_snmpd()
{
  if [[ -f "$SNMPDIR/bin/snmpd" ]];then
    $SNMPDIR/bin/snmpd -Cc $SNMPDIR/conf/snmpd.conf -Lo &
    chmod 777 /var/agentx/master
  fi
}
start_pdu()
{
    #run smartPDU
  if [[ -f "$APPDIR/smartPDU"  ]];then
    $APPDIR/smartPDU &
  fi
}
led_on()
{
    #light led
    echo 160  > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio160/direction
    echo 161 > /sys/class/gpio/export
    echo in  > /sys/class/gpio/gpio161/direction
    echo 162 > /sys/class/gpio/export
    echo in  > /sys/class/gpio/gpio162/direction
    echo 131 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio131/direction
    echo 136 > /sys/class/gpio/export
    echo out  > /sys/class/gpio/gpio136/direction
    echo 1 > /sys/class/gpio/gpio136/value
}
start_lcd()
{
    # light lcd
    led_on
    # fbinit
    if [[ -f "$APPDIR/Qt_Test"  ]];then
      $APPDIR/Qt_Test -platform linuxfb:fb=/dev/fb1 &
    fi
}



app_start()
{
  case "$1" in
    smartPDU)
      start_pdu
      ;;
    snmpd)
      start_snmpd
      ;;
    Qt_Test)
      start_lcd
      ;;
    all)
      start_snmpd
      start_pdu
      start_lcd
      ;;
    *)
      exit 1
  esac
}
app_stop()
{
  case "$1" in
    smartPDU)
      killall $1
      ;;
    snmpd)
      killall $1
      ;;
    Qt_Test)
      killall $1
      ;;
    all)
      killall snmpd smartPDU Qt_Test
      ;;
    *)
      exit 1
  esac
}


#app_start all

start_snmpd
sleep 4 

start_pdu

sleep 1
start_lcd


if [[ -f "/mnt/UDISK/app/smartMonitor.sh" ]];then
  sh /mnt/UDISK/app/smartMonitor.sh &
fi

# sleep 20

# led_on

# fi